Rotary go kart

clive · November 20, 2020, 06:53:22 PM

Great that this is coming along. (love the mudguards)
You obviously have experiance from the other car, but seeing the tank, if its not foam filled you will need a swirl pot and then as Jon says just a Walbro 255 pump

baloo · November 20, 2020, 07:14:09 PM

Quote from: boosted on November 20, 2020, 06:29:43 PM
Yes you can it unclips and you can extend the pick up. Theres a syphon part you can junk. I did similiar in my alloy tank in my westfield.

Sent from my SM-N950F using Tapatalk

i will remove the pump from the tank and have a looksy, might have to make a tool to undo that big ring thought it seemed very tight

boosted · November 20, 2020, 07:33:06 PM

Big masonary screwdriver...hit with a hammer.

Sent from my SM-N950F using Tapatalk

baloo · November 23, 2020, 05:06:58 PM

Quote from: boosted on November 20, 2020, 06:29:43 PM
Yes you can it unclips and you can extend the pick up. Theres a syphon part you can junk. I did similiar in my alloy tank in my westfield.

Sent from my SM-N950F using Tapatalk

did you use an RX8 pump in an alloy tank ? if so how did you hold it in ?

boosted · November 23, 2020, 06:02:13 PM

You tank the hole fuel pot out so internal reg and filter remain..that can be seperated to allow suction on bottom tank by lengthing with piece of alloy or suchlike. Electrical wires lenthen and pipe to outlet .
Tricky bit is cutting whole and welding on studs and making a gasket. Holes can be drilled for said studs on outside rim of fuel pot.

Sent from my SM-N950F using Tapatalk

baloo · November 23, 2020, 07:23:43 PM

Quote from: boosted on November 23, 2020, 06:02:13 PM
You tank the hole fuel pot out so internal reg and filter remain..that can be seperated to allow suction on bottom tank by lengthing with piece of alloy or suchlike. Electrical wires lenthen and pipe to outlet .
Tricky bit is cutting whole and welding on studs and making a gasket. Holes can be drilled for said studs on outside rim of fuel pot.

Sent from my SM-N950F using Tapatalk

so you drilled new holes in the top flange of the pump and bolted it to tank ? thats what i was wondering about or whether i had to use the screw down collar which would mean i had to make up a new screw thread to weld onto tank

boosted · November 23, 2020, 07:30:38 PM

Yes..pita but once done. Made a seal out of ptfe.

Sent from my SM-N950F using Tapatalk

Mr Spiller · November 26, 2020, 10:33:56 AM

These are cheap

Sent from my iPhone using Tapatalk

boosted · November 26, 2020, 10:35:53 AM

Ive had multiple sets of team dynamics. Good lightweight wheels! I had a nice set on my silver rx8 s type.

Sent from my SM-N950F using Tapatalk

Mr Spiller · November 26, 2020, 10:38:14 AM

Quote from: boosted on November 26, 2020, 10:35:53 AM
Ive had multiple sets of team dynamics. Good lightweight wheels! I had a nice set on my silver rx8 s type.

Sent from my SM-N950F using Tapatalk

Yep
BTCC wheels
If they were 18 I'd have have

Sent from my iPhone using Tapatalk

baloo · November 26, 2020, 06:16:57 PM

thank you for that they would be ok for the fronts would like wider for the rear im on the trail of some

baloo · November 26, 2020, 06:21:59 PM

ok so whats all this about ? ive got the brake pedal assembly out and there is a cable fitted to the top with a proper nipple but the steel cable only goes down and round the pivot of the pedal whats it for den ?

baloo · November 26, 2020, 06:27:23 PM

started folding up the pedal box seemed to be going good for a while $:-\$

baloo · November 26, 2020, 08:52:25 PM

baloo · November 26, 2020, 08:56:17 PM

made a bit of an error there but the man who dident make a mistake never made anything i seem to remember being told lol