Dyno tommorow! What power with my setup?

Started by Kash_, December 22, 2008, 03:22:09 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Kash_

Hey peeps, I\'m getting my Rex dynoed tommorow.. what kind of power figures do you think I\'m looking at?

Streetport engine
Garrett T60-1
3" exhaust sytem
1600 secondaries
BNR Fuel pump

Lets see who gets closest :wiggle

AndyGen3

What boost you running ?

Judging by your time for the qtr mile id say 420 @ the fly...

Andy

ash

Kash - I\'ll throw in 350rwhp into the mix...just a guess really :Thumbs-up

BlitzBoy

"Piston Killa" 3rd Gen\'94 \'Oldone Racing Full Bridge Ported REW 13b engine with SCR seals\'. HKS T51 KAI turbo BBM mapped Motec ECU

JDS/HKS Street Class Championship Runner up 2011
Rotorstock winner 08,09
http://pistonkilla.blogspot.com/
old spec HB T51 470 @ wheels @ 1.2 BAR, 555 @ fly 10.46 @ 130 @ 1.25 Bar
new spec FB T51 482 @ wheels @ 1.15 BAR, 570 @ fly

New Project
"el fénix" RX2 by Mark & Mark

Will66

I reckon you\'ll be getting 370 at the wheels.  Just a guess!
RX8 High Power, Cusco Coilovers, Dotz wheels and flames. Shoe Size 12
 
Apparently putting details of your car spec in your signature means the nice folks on exile-rotorsport think you\'re a fool.  I can think of no higher compliment!

"Eat it with a chopstick!"

Kash_

My quarter mile time was on my old setup T04e (331rwhp @ 0.9 bar)

I\'ll be running 1.2 bar on this turbo....

BlitzBoy

"Piston Killa" 3rd Gen\'94 \'Oldone Racing Full Bridge Ported REW 13b engine with SCR seals\'. HKS T51 KAI turbo BBM mapped Motec ECU

JDS/HKS Street Class Championship Runner up 2011
Rotorstock winner 08,09
http://pistonkilla.blogspot.com/
old spec HB T51 470 @ wheels @ 1.2 BAR, 555 @ fly 10.46 @ 130 @ 1.25 Bar
new spec FB T51 482 @ wheels @ 1.15 BAR, 570 @ fly

New Project
"el fénix" RX2 by Mark & Mark

Kash_

Quote from: BlitzBoy;567782what dyno you using tomorrow?

Not sure, I\'ll find out tomorrow :driving

BlitzBoy

lol where ya going tomorrow which garage?
if its a Dyno Dynamics, my guess at 1.2 BAR 415 rwhp
"Piston Killa" 3rd Gen\'94 \'Oldone Racing Full Bridge Ported REW 13b engine with SCR seals\'. HKS T51 KAI turbo BBM mapped Motec ECU

JDS/HKS Street Class Championship Runner up 2011
Rotorstock winner 08,09
http://pistonkilla.blogspot.com/
old spec HB T51 470 @ wheels @ 1.2 BAR, 555 @ fly 10.46 @ 130 @ 1.25 Bar
new spec FB T51 482 @ wheels @ 1.15 BAR, 570 @ fly

New Project
"el fénix" RX2 by Mark & Mark

Kash_

My previous dyno on my old turbo HKS T04e @ 0.9 bar



http://www.youtube.com/v/5mre4CSLSbw&hl=en&fs=1">http://www.youtube.com/v/5mre4CSLSbw&hl=en&fs=1" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="425" height="344">

Kash_

Quote from: BlitzBoy;567787lol where ya going tomorrow which garage?
if its a Dyno Dynamics, my guess at 1.2 BAR 415 rwhp

It\'s one that Jay and Eds recommended, I\'m pretty sure its a Dyno Dynamics

mx1311

420rwhp is my guess

nice backflip in powergraph lol

Ada7

I\'m gonna say 384rwhp. Is a good a guess as anyone else :D

Adam
I AM HERCULESIAN
Rex II - The Bridgeport years http://mazdarotaryclub.com/forum/index.php?topic=82902.0

Kash_

Quote from: mx1311;567790420rwhp is my guess

nice backflip in powergraph lol

lol good old standard clutch :Giggle

skybusr34

i think it will be 431.6 at the fly. as long as the ambient air temp is below 15`c.    

all a guess though :-)
if i had 8 hour to cut down a tree. i`d spend 6 sharpening the axe