HELP: Any tips for Removing Pilot Bearing from the Eccentric shaft

RotorHeid · November 05, 2006, 06:36:10 PM

WoW!, quick reply from everyone, well said!!,
just finish my haggis and oat meal.

antnicuk · November 05, 2006, 06:37:38 PM

thanks clive

, a circular one will not cut along it, just wondered what shape tool would

kev-yorks · November 05, 2006, 06:42:17 PM

Quote from: oldoneThere you go overdoing it again......:spank 6" is more than adequote(sp)..:wiggle

No when i go overkill Era i get the gas axe out!
Kevin

RotorHeid · November 05, 2006, 06:42:23 PM

If not move! , use a bolt(grip by vice) to screw in and tug the bush out!

oldone · November 05, 2006, 06:44:37 PM

Quote from: ian duncanWoW!, quick reply from everyone, well said!!,
just finish my haggis and oat meal.

You Scottish are differant(sp).......haggis and oat meal ?,sounds like horse food....:wiggle

RotorHeid · November 05, 2006, 06:49:26 PM

Wooo! ,bet ootya! me behind yer back at auld schoo met:eek

oldone · November 05, 2006, 06:59:22 PM

Quote from: ian duncanWooo! ,bet ootya! me behind yer back at auld schoo met:eek

As long as you bring some haggis for me to sample bud !!!!!!!!!:Typing

RotorHeid · November 05, 2006, 08:03:58 PM

Okay! with barrels of whiskies

Timrxmotors · November 05, 2006, 08:13:09 PM

Quote from: oldoneSteel porting bits bud....:evillaugh :cool destroy it and yank it out......eccentric shaft material is very hard.....:2eek so dont be bothered about a mark or two as the outer shell of new bearing covers it !!!!!!!!:D :Typing
The shaft is far from hard,you can cut it with a hacksaw.The bearing case is hard,and the hole it goes into must stay perfectly unmarked,any burrs will push and deform the bearing.If you chisel it out you will be for ever trying to make the hole round again,I mean for ever! You need the proper puller,even if all the needles have gone,the puller will remove what\'s left,easily.

oldone · November 05, 2006, 08:22:10 PM

Quote from: Timrxmotors
Quote from: oldoneSteel porting bits bud....:evillaugh :cool destroy it and yank it out......eccentric shaft material is very hard.....:2eek so dont be bothered about a mark or two as the outer shell of new bearing covers it !!!!!!!!:D :Typing
The shaft is far from hard,you can cut it with a hacksaw.The bearing case is hard,and the hole it goes into must stay perfectly unmarked,any burrs will push and deform the bearing.If you chisel it out you will be for ever trying to make the hole round again,I mean for ever! You need the proper puller,even if all the needles have gone,the puller will remove what\'s left,easily.
Oh! you are such a perfect princess....:wiggle :evillaugh :guinness :Hammer :cool :2Rolleyes

antnicuk · November 05, 2006, 08:40:19 PM

only problem is i have no lip left at the outside end of the casing?, does the puller grip the outer lip or the inner lip?, i think i still have some lip on the inner edge

anyone have a puller i could borrow?

Grizzly · November 05, 2006, 11:56:41 PM

Its easy, Not to sound Rough but i Distroyed mine with a Screw driver and a Hammer.

I tryed all sorts at first, things like getting a few Washers that just fit inside the bearing then put a Bolt through them and a Slide hammer on the end, that worked ok to a point then the Washers started to go out of Shape and it just slipped off, So i lost My Rag and hit it with a Hammer