Kermit II (K-II) Triple rotor rebuild project

Started by Sicknote, September 23, 2012, 09:26:17 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

leeroy_25

Git!!
Turn that into months and I am still not close!
I cannot remember if I had your e-mail address in the end or not now.. But could you let me know it again as I may have potential proposition for you!

Cheers
Lee

Sicknote

Sounds interesting, dave_301@hotmail.com   :D

Quote from: leeroy_25;852675Git!!
Turn that into months and I am still not close!
I cannot remember if I had your e-mail address in the end or not now.. But could you let me know it again as I may have potential proposition for you!

Cheers
Lee

Sicknote

Ok, I got there a bit late so we didn\'t get onto the seat rails, so instead finished making and tacking the rest
of the exhaust.  :D














Very pleased with the end result   :D   :thumbsup:





Grant Monkhouse

What are those canisters in the boot leading under the car? I think they say nitro on them? Suspension remote reservoirs???

Also with the exhausts will you get much of the gases going out through passenger side muffler?

Sicknote

Yep, they\'re the Nitron suspension remote reservoirs .

I think it will be a 45/55 % split, we\'ve channeled inside the split pipe join to push gasses accross to the left side.  :)

Quote from: Grant Monkhouse;852697What are those canisters in the boot leading under the car? I think they say nitro on them? Suspension remote reservoirs???

Also with the exhausts will you get much of the gases going out through passenger side muffler?

Grant Monkhouse

All good then, was thinking if there wasn\'t some kind of divertor it wouldn\'t be used.

What are you flat bottoming and making the diffuser out of?

Sicknote

Aluminium plating for the majority of the floor and we\'ll be making a fibreglass rear diffuser ourselves.  :)

Quote from: Grant Monkhouse;852699All good then, was thinking if there wasn\'t some kind of divertor it wouldn\'t be used.

What are you flat bottoming and making the diffuser out of?

Casey

Looking better and better every time I look in here, great work by all involved :mmmm

Really looking forward to seeing (and hearing) this monster on track sometime later this year.
RX-8 230 Bridgeported: Racing Brake Disks & 4 pot front calipers,Full Racing Beat (RB) SS Exhaust system,RB ARB's F & R,RB REVI intake,Tein MonoFlex Coilovers & front strut brace.
RX-7, KIMI 1, 1st Gen S2, Silver,1983 - SORN
RX-7, KIMI 2,^^Ditto - now sold
RX-7, KIMI 3, 1st Gen S3, Red,1984

Sicknote

You and me both Malcolm, she\'s gunna be a bit scarey I rekon !!  lol

Quote from: Casey;852705Looking better and better every time I look in here, great work by all involved :mmmm

Really looking forward to seeing (and hearing) this monster on track sometime later this year.

leeroy_25

Hi Dave,
Hopefully you got my e-mail?

Cheers
Lee

Sicknote


Grant Monkhouse

Struggling with email, just post it on here, then all is nosey buggers can know what your talking about

leeroy_25

Ha ha!!! Secret squirrel!!
Maybe check your junk? Dave_301 at hotmail dot com right? it\'s in my sent items. Can try re-sending it. In case my phone was having an off day!

Sicknote

I\'ve got that one Lee, will reply after work today.  :)

Quote from: leeroy_25;852753Ha ha!!! Secret squirrel!!
Maybe check your junk? Dave_301 at hotmail dot com right? it\'s in my sent items. Can try re-sending it. In case my phone was having an off day!

Sicknote

A parcel arrived today, not a lot to show for over a grand but these are the Three 2000cc injectors (left) and
the three 1000cc injectors (right) and the fuel rail.  :D