Power fc English manual?

YAU730 · October 20, 2011, 05:48:41 PM

Got my power fc in today but manual all in jap, anywhere where u can dl English manual? N what r the steps of installing the ecu? Straight plug in a drive off or plug in n leave it sitting for a certain amount of time to let the euc pick up?

L18M · October 20, 2011, 08:47:47 PM

did you get commander also?

Disconnect Power
Unplug stock ECU
Plug in PowerFC ECU
Reconnect Power
Start Car, let it idle for approx 10 minutes before doing anything
Turn on aircon, let it readjust its idle and wait about 10 minutes
Turn on demister, let it readjust its idle and wait about 10 minutes

wolfie1 · October 20, 2011, 09:09:02 PM

look on apexi usa site

neil_jdmr · October 20, 2011, 10:34:38 PM

I got my english manual in pdf from apexi-usa.com

YAU730 · October 21, 2011, 01:51:11 AM

Quote from: L18M;795501did you get commander also?

Disconnect Power
Unplug stock ECU
Plug in PowerFC ECU
Reconnect Power
Start Car, let it idle for approx 10 minutes before doing anything
Turn on aircon, let it readjust its idle and wait about 10 minutes
Turn on demister, let it readjust its idle and wait about 10 minutes

Yeah, got the old commender, i might end up selling it later for the el ver or might just sell it overall...

Pip told me to pretty much do that to but i thou i would go on here to make sure am going to carry it our right, thanks, will need to find somewhere to do this then as my neighbors are going to go mad running my car that long!

YAU730 · October 21, 2011, 01:51:41 AM

Thanks guys...

re japi · October 21, 2011, 04:23:07 AM

Check this site. Helped me alot. And there you can find that manual too...

http://www.paulr33.com/powerfc-faq/powerfc-faq.htm

YAU730 · November 08, 2011, 04:33:18 PM

Going to try n install this myself now, where is standard ecu located n any things to take apart to access it if so?

fil_auto · November 08, 2011, 05:07:20 PM

passenger side footwell, left handside, remove kickplate, then panel, easier access

YAU730 · November 12, 2011, 01:02:48 PM

Quote from: fil_auto;797980passenger side footwell, left handside, remove kickplate, then panel, easier access

Thanks,

Just installed the power fc,

10mins idle (Was bouncing rev from 1-1.5k for 2-3 then settled)
then demister for 10mins (Was bouncing rev from 1-1.5k for 2-3 then settled)
Then air con (Was bouncing rev from 1-1.5k for all the way)
switched air con off and drive back home (15miles)

Drives really smooth and fine but revs still bouncing 1-1.5k, is this normal as
its still learning or have i done something wrong and need to start over again?

L18M · November 12, 2011, 01:08:48 PM

you fixed the o2 sensor?

YAU730 · November 12, 2011, 04:06:25 PM

Forgot to add that i also disable the boost controller setting as i don\'t have one which is:

ETC, 4.02 F/B Control.

is this boost controller?

Liam, whats o2 sensor?

YAU730 · November 12, 2011, 11:43:59 PM

Quote from: L18M;798525you fixed the o2 sensor?

Just realized that was the 02 sensor that i disabled, will switch it back on 2moro.

Anyone know where the boost controller menu is for switching on and off?

L18M · November 13, 2011, 12:44:02 AM

o2 sensor = lamda sensor
then spark plug looking thing on the downpipe with 1 (iirc) wire poking out of it.

YAU730 · November 13, 2011, 11:29:25 AM

Quote from: L18M;798608o2 sensor = lamda sensor
then spark plug looking thing on the downpipe with 1 (iirc) wire poking out of it.

Hm.... should be disable in a way then as mines snapped, will enable later and see if any changes or might start again if i have time.