gaskets

[Kenji]

I\'m soon getting my FD, and am on the hunt for a spare UIM and intake elbow, which I want to paint.
 
Are there gaskets between the UIM and LIM, UIM and thrlottle body, and throttle body and intake elbow?
And if so, can they be re-used?
 
I know form my 1JZ-GTE in my previous car that Toyota had inserted steel gaskets, that could be cleaned and then re-used. Did Mazda do this too, or do I have to get new gaskets?

[RXSpeedy]

Yes you have a gasket between the UIM and the LIM and between the UIM to the throttle body. I bought mine from Jon at Atomic Rex. I believe there mostly normal gasket material but sometimes theres metal ones

[AtomicRex]

We have all of them in stock if you want them.
 
We supply our own version of the UIM to LIM as well as LIM to Engine.  I have the OE versions of the other gaskets in stock though.
 
We also do exhaust manifold gaskets at about half the price of OE ones.

[davehg]

normally a reusable metal gasket betweek UIM and LIM and the one between TB and UIM is normally paper from what i have found in the past.

[HK FD3S]

We have all of them in stock if you want them.
 
We supply our own version of the UIM to LIM as well as LIM to Engine.  I have the OE versions of the other gaskets in stock though.
 
We also do exhaust manifold gaskets at about half the price of OE ones.

Hi, Do you happen to have the 99spec y pipe gaskets?

Ta

[Kenji]

We have all of them in stock if you want them.
 
We supply our own version of the UIM to LIM as well as LIM to Engine. I have the OE versions of the other gaskets in stock though.
 
We also do exhaust manifold gaskets at about half the price of OE ones.

How much for the Atomicrex versions of these:
 
2x LIM to UIM
2x UIM to Throttle Body
2x Throttle Body to Intake Elbow
 
Sent to The netherlands please?

[PDale]

I\'m pretty certain there is no gasket between throttle body and intake elbow. If you think about it logically, it wouldn\'t make a difference if air entered a gap between the TB and elbow as it hasn\'t been \'measured\' yet. Its only when its entering the system past the throttle body that you need to worry, as its \'unmetered\' air and will screw up your idle, etc.

[philiwily]

There is a large O ring that fits in a groove in the throttle body for the throttle body to elbow connection.
PDale is correct in that it is unmetered air but your best not having any boost leaks, so if it needs replaced, replace it.

[AtomicRex]

YOu are looking at potentially 2 bar of pressure in there its possibly best you do have some sort of seal in there
 
The UIM to throttle body gaskets are £11.40 +VAT (£13.40)
The throttle body to elbow gaskets are £13.19 +VAT (£15.50)
The UIM to LIM gaskets are £19.99 +VAT (£23.49)
 
Excluding delivery would be £104.76
 
Did you get the UIM? If not I will do that for £20 and I can work out the delivery based against all of it.
 
(These VAT prices are worked out at 17.5%)

[SiH]

I\'m pretty certain there is no gasket between throttle body and intake elbow. If you think about it logically, it wouldn\'t make a difference if air entered a gap between the TB and elbow as it hasn\'t been \'measured\' yet. Its only when its entering the system past the throttle body that you need to worry, as its \'unmetered\' air and will screw up your idle, etc.

There is a large rubber triangle shaped \'o\' ring that sits between in a groove on the TB. True that a leak here would not make a difference to fuelling , however it\'s a leak, and any leak means that the turbo just has to work harder to provide the required boost pressure. So you get more lag, and more heat generated. So basically, it\'s bad.

[PDale]

^^^^^^^^
cool, good info to know. As everyone else has said, might as well replace it :3gears-rh

[Kenji]

YOu are looking at potentially 2 bar of pressure in there its possibly best you do have some sort of seal in there
 
The UIM to throttle body gaskets are £11.40 +VAT (£13.40)
The throttle body to elbow gaskets are £13.19 +VAT (£15.50)
The UIM to LIM gaskets are £19.99 +VAT (£23.49)
 
Excluding delivery would be £104.76
 
Did you get the UIM? If not I will do that for £20 and I can work out the delivery based against all of it.
 
(These VAT prices are worked out at 17.5%)

You wouldn\'t happen to have any type of intake elbow as well now, would you?

[philiwily]

I have a spare standard one, its a silver one.
You can have it for the cost of postage.

Phil

[AtomicRex]

If Kenji is interested do you want to send the elbow down to me Phil, and I can stick it in the box?  The postage will be a lot cheaper then

[Kenji]

Phil, that would be nice of you, thanks.
 
 
AtomicRex:
 
I would like the following then:
- UIM
- 1 gasket LIM/UIM
- 1 gasket UIM/throttle body
- 1 gasket throttle body/intake elbow
- intake elbow
 
and I\'m also looking for 2x 63mm and 2x 70mm silicone couplers in black. Do you have those as well?
 
How much for the above including shipping to Rotterdam, The Netherlands?
 
And how can we sort out the shipping for Phil??