Custom Rear Tail light modifications.

[Carbon RX]

Not being happy with my aftermarket lights I\'ve wanted to replace with 99 spec versions that have the round break lights apposed to the early versions that are square an much less pleasing to the eye. I decided instead of forking out £100\'s to have ago at customising my original ones. Am documenting for anyone interested in doing the same!

To get the outside lense off you have to remove the six screws holding on the rear before using a heat gun as pictured to loosen the glue... Have patience with this bit it\'s prob the hardest part!
http://i1208.photobucket.com/albums/...ersion/gun.jpg

View of back With screws removed
http://i1208.photobucket.com/albums/...n/rearcomp.jpg

Front of light, you can see the lens coloration as st.
http://i1208.photobucket.com/albums/.../frontcomp.jpg

View of seam between front and rear, I used a screw driver to open up gentle applying heat at the same time.
http://i1208.photobucket.com/albums/...n/sidecomp.jpg

Two pieces separating whoop!
http://i1208.photobucket.com/albums/...n/halfopen.jpg

close up!
http://i1208.photobucket.com/albums/...n/zoomopen.jpg

An finally apart
http://i1208.photobucket.com/albums/...on/allopen.jpg

The inner lenses are held with one screw each and clips the opposite sides, the clips also have glue so use heat again to ease out. Note the glue melts before plastic so go easy and should have no problems.
http://i1208.photobucket.com/albums/.../innerlens.jpg

all apart
http://i1208.photobucket.com/albums/...n/allapart.jpg

Inner lenses removed and ready for modifications.
http://i1208.photobucket.com/albums/...rlensesout.jpg


As im going to the trouble of doing this myself, i feel would be waste of an opportunity to simply mask three 3" circles to imitate the \'99 spec lights, I have a few ideas of what im going to do, however anyones input at this stage would be appreciated..??

TBC......

[Carbon RX]

I am currently toying with the idea of striping the brake lights whilst using a simple rotor design for the indicators, Im not sure i have seen this done plus dont see why all three shapes have to be the same??
Either way i have also decided not to mask and spray but to get the images cut professionally by a graphics company then overlaid, this im hoping will give a clean and more pro look....
Potential indicator design - might need a lil simplification

[Carbon RX]

A simplified rotor image i could use...

 
Some ideas (early) to which i could use, not sure im quite there yet!

you get the idea :cool:

[Lil-Steve]

Perhaps the simple rotor motif for all three lights and then some black film to black out the centres? I\'ve seen something similar to get the lights to have ring appearence rather than the solid circle and it looks very good.

[Carbon RX]

Perhaps the simple rotor motif for all three lights and then some black film to black out the centres? I\'ve seen something similar to get the lights to have ring appearence rather than the solid circle and it looks very good.

Definately abit more refined, Will keep working on ideas....

[probedb]

I seem to remember someone doing this but it was probably on rx7club. Go for it tho

[Bobbit]

I did the 3 rotor on mine looks great, using the iPhone otherwise id link my post.

[Carbon RX]

I did the 3 rotor on mine looks great, using the iPhone otherwise id link my post.

Im aware that im by far NOT the first person to try this , however when finding information on how-to i couldnt get anything better than a descriptive list. It has been very helpfull getting them apart, but i think thats where things change for all.
 
Please link any previous works undertaken previously by anyone as i would appreciate the visual after effects etc to help aid my decision :god :Thumbs-up

[Bobbit]

click

Here you go.

[Carbon RX]

Mucho Gracias Bobbit !!!!!
 
I likey I likey :Giggle
 
Has helped me refine my plans no end! :Thumbs-up