make-over!

ENVYD · December 29, 2009, 10:26:43 PM

yup, defo, that’s why i have tried to make the skirts look original.

i hope to have the exterior of the car finished by the end of jan mate!

karl_tate · December 29, 2009, 10:53:06 PM

ENVYD · December 29, 2009, 10:54:50 PM

i love that silver one! can i hell find that lower lip spoiler!

shaunwil · December 29, 2009, 10:54:52 PM

Outstanding work. Looking forward to the results !

Shaun

karl_tate · December 29, 2009, 11:00:49 PM

which one, there is two hahaha...

go over to rx7club, there is a vendor on there that sells them.

MaLicE · December 29, 2009, 11:02:29 PM

have to say your work is stunning! wish i had the space and half the skill to pull off what you are! if you get the propper tuck and stance you will have one of the nicest fd\'s in the uk! i like some kitted fd\'s but the stock bodys are soooo nice!

have you had the rear arches rolled or pulled??

ENVYD · December 29, 2009, 11:02:43 PM

Quote from: shaunwil;662105Outstanding work. Looking forward to the results !

Shaun

thanks mate

ENVYD · December 29, 2009, 11:03:20 PM

Quote from: karl_tate;662108which one, there is two hahaha...

go over to rx7club, there is a vendor on there that sells them.

sorry bud, the lower one lol

i have just found it with shine auto

ENVYD · December 29, 2009, 11:05:56 PM

Quote from: MaLicE;662109have to say your work is stunning! wish i had the space and half the skill to pull off what you are! if you get the propper tuck and stance you will have one of the nicest fd\'s in the uk! i like some kitted fd\'s but the stock bodys are soooo nice!

have you had the rear arches rolled or pulled??

thanks very much mate, make its worth while with hard work when you get good comments!

yeah they have been rolled and pushed out a very small amount!

steven

MaLicE · December 29, 2009, 11:12:29 PM

you need to lower it so the rubber is stuck in the arches get a propper hellaflush look on it! will be amazing!

ENVYD · December 29, 2009, 11:17:56 PM

yeah i will be doing that bud! think the skirts will be about 30mmm off the floor ( i think) as i give it a quick measure!

ENVYD · December 30, 2009, 05:52:26 PM

a few more lil bits dont today,
got some new masking on it read for the paint on sunday, just need to move it first before i do the wheels:

and a few parts i was not happy with, so they had to be re-done:

then a quick dust over with whie primer:

and finished with start to some the cone on the sub box before i give it back:

and i was bored, so i tuck a photo with the heater lol

thanks
steven

MaLicE · December 30, 2009, 08:51:14 PM

has something reacted where the vent goes in the wing?

ENVYD · December 30, 2009, 09:47:00 PM

no mate its the old tiger seal, i have left it on to line the vent back up as some of the pins are missing off the vent, so the tares in the tiger seal help with lining it back up!

batman · December 30, 2009, 09:59:52 PM

looking good envy you not worried about weight then with that maaahoosive build in the back lol .
id agree with malice bonded on side skirts scare me on knock and cracks everywhere but shall look schwweeet