Clutch - 6 puck or twin plate

[Kash_]

I have a ACT 6 puck and it\'s holding perfectly fine all the way to 1.2 bar It\'s a bit on and off but you can still ride it if you need to

[karl_tate]

thats good enough for me dude, do you happen to know which one it is though??

where did you get it from??

[Kash_]

I got mine from Whifbitz... As far as I know it\'s the ACT 6 Puck Unsprung clutch, not the Street/Strip one... like this one http://www.rx7store.net/product_p/zx3-hdr6.htm

[karl_tate]

thanks for that mate :Thumbs-up

[Kash_]

no worries dude

[Erdin]

I can get spec clutch\'s if any one wont one. The spec stage 3 plus feels like a factory clutch and can take over 450rwh.

Pm me if interested.

[hairyhoover]

i also have the act 6 puk as well - good clutch!

[leeroy_25]

Hi.. I was recommended the XTD 3 stage 6 puck sprung clutch by a dude in NZ who builds rotarys for street, drag and track use. he says he has used a few of them and they are a pretty good feel for a six puck and you cannot get another clutch close on price.. I have looked and they seem very reasonable! if they do what they say on the tin you are laughing. Think I might take a punt on one! Same about the current exchange rate though! Bring back 2USD:1GBP!!

here is the link:
Item number: 200266141394

Let me know what you reckon.

[karl_tate]

that looks good.
 
ive been looking at this one http://www.rx7store.net/product_p/zx3-xtr6.htm
 
i think i will be ordering one pretty soon.

[leeroy_25]

OKay guy\'s I finally fitted my new clutch! See this link:
http://www.mazdarotaryclub.com/forums/showthread.php?p=556917#post556917

I used an XTD stage 3 clutch I as recommended by a rotary specialist in New Zealand. The clutch came from USA via ebay and was a bargain!

http://cgi.ebay.com/ebaymotors/RX-7-RX7-93-99-XTD-STAGE-3-RACING-CLUTCH-KIT_W0QQcmdZViewItemQQ_trksidZp3286Q2em63Q2el1177QQhashZitem200274022864QQitemZ200274022864QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories




Best bit is I drove it out of the garage and it is very close to stock feel! okay a little bit heavier and slightly more bite but nothing like I expected!
I would definately recommend this to anyone looking for one, especially if it holds up a rated!

Lee

[karl_tate]

looks good, what kind of torque can it handle, i still havent got one sorted, have been talking with some one in auz that can offer a twin plate with pull to push kit for around £600 i think it was.

what was the final price you paid for it and did you get stung with tax\'s etc??

[leeroy_25]

Hi There, I can\'t remember the torque rating off hand. there is a link to the ebay add in my other post about fitting rear oil seals. or just type XTD stage 3 rx7 in ebay worldwide.. I didn\'t get stung for tax fortunately this time! So depends on current exchange rate what is comes to.. But it was a bargain!!

[karl_tate]

cool, just had a look, i dont think i will risk it as i dont want to get it in and then start slipping after the run in miles.

cheers

karl

[leeroy_25]

Blimey.. what power/torque you aiming for then??!

[karl_tate]

well im on a single turbo, not really sure on the power but i had 340rwhp unported at 0.8 bar