Pix of my FD..

chrisJDM · October 24, 2008, 11:34:45 AM

very nice great pics!

Ada7 · October 24, 2008, 11:59:33 AM

Thats some lovely polishing on the housings.

Adam

Swanny_UK · October 24, 2008, 11:46:59 PM

Second Ada7\'s comment - lovely polishing!

interloper393 · October 24, 2008, 11:54:36 PM

what do they use for all thos funky bits when polishing? i do a bit n get no where near that finish!! people know n wont tell me lol...

leeroy_25 · October 25, 2008, 09:39:31 AM

Same as that! That is some top quality \'mould polishing\' standard work. Unless you have cheated and it\'s plating or paint? If it\'s polishing that must have cost a pretty penny to get done! And the engine bay will look blinding either way! Tempted to do that on my rebuild now!! Thanks for the idea!

Lee

vest_racing · October 27, 2008, 12:00:34 AM

Thanx guys...

The housings are polished, we don`t cheat on anything here...:Giggle

vest_racing · November 14, 2008, 07:51:13 PM

Engine pics..

vest_racing · November 14, 2008, 07:57:36 PM

Kevin · November 14, 2008, 09:51:15 PM

Car porn!!

karl_tate · November 14, 2008, 11:03:41 PM

intake looks nice

so whats the spec then??

vest_racing · November 15, 2008, 02:18:04 PM

Quote from: karl_tate;554642intake looks nice

so whats the spec then??

What spec do you need?..:p

ENVYD · November 15, 2008, 02:27:20 PM

did you say that the engine is going to rev up to 10-11k or something like that?

also are you going N/A or turbo\'d

vest_racing · November 15, 2008, 02:29:59 PM

Quote from: ENVYD;554780did you say that the engine is going to rev up to 10-11k or something like that?

also are you going N/A or turbo\'d

Turbo.

That will depend on where I have the power..:yes

But with that ecc I will have no flex, so I can do high revs on this one yes..:Giggle

vest_racing · November 15, 2008, 02:53:42 PM

Quote from: karl_tate;554642intake looks nice

so whats the spec then??

New Custom inlet.
New 85mm throttlebodie.
New 6x 1680cc injectors.
New fuel rails.
New 2 piece crank
New rotor housings
New FD side plates
New FC (s4) rotors
New 20b stationary gears
New bearings
New oil pump
New rear counterweight
New springs/seals/gaskets etc
New SCR apex seals
New Strud kit 12.7mm & machining
Lighting of rotors 200-250g each
Balanced rotating assembly
Front stack/front cover/sump etc etc
Center bearing oil feed
Cooling upgrade
Oiling upgrade
HKS twin plate clucth
Custom exhaust manifold
Garrett GT4202R Turbo 30PSI of boost
Tial 60mm wastegate
5" exhaust system

Aeromotive A2000 feed pump
3x Aeromotive A1000
3x Aeromotive fuel pressure regulators
2L surge tank
70L fuelcell
Earls hoses

Here are some spec, probably left something out..:Hammer

ENVYD · November 15, 2008, 03:06:06 PM

Quote from: vest_racing;554787New 6x 1680cc injectors.

30PSI of boost

:2eek crazy, crazy!

can not wait to see this running lol!