new member,hi all

[pdtaylor18]

sounds like its gone.  Sounds should be similar and rear rotor is always prone to going pop before front.  There are various ways of seeing if a seal has gone,compresion check is the one way but then there are a few others. Not sure where they are but do a search on here or on the rx-7 owners club.
sometimes tips can go and ECU\'s will never pick it up, they are looking at sensors, maybe a sensor has failed and caused it to go.
I put 99 ron fuel whenever i can as i have a jap uprated ECU so i have to go careful.

[doddy]

@flatout - would the car get you to Brae?

I visited Eddie Doyle there once and he\'s a rotary nut e.g. about 5 rotor housings sitting in his workshop.  Quite sure he has the compression tester too.

Irish fuel is the same as UK fuel no?!  My cars go alright on it anyway :>

[flatout]

been talking to Eddie Doyle,he will do the rebuild for me,he is very good at his job i have been told,fair price aswell,i will have to take the car to uk for a map do, nobody here will go near the microtech ecu,i wouldnt change the ecu as this a good one and the apex pc is crazy money for the fc

[flatout]

been talking to Eddie Doyle,he will do the rebuild for me,he is very good at his job i have been told,fair price aswell,i will have to take the car to uk for a map do, nobody here will go near the microtech ecu,i wouldnt change the ecu as this a good one and the apex pc is crazy money for the fc

[BenLewisMav]

The guy you want to get in touch with is Pip Gardner @ WGT Auto Developments, he\'s an official Microtech dealer (supplier, fitter and tuner) and has spent some 20+ years tuning rotaries.  
Havent heard anything but praise for him, just finished dealing with him as he supplier me with an LT-10s, dash unit and laptop dongle, he seems like a complete legend.
Check out http://www.wgtautodevelopments.co.uk/, think it\'s about £150 for a full tune?

[flatout]

The guy you want to get in touch with is Pip Gardner @ WGT Auto Developments, he\'s an official Microtech dealer (supplier, fitter and tuner) and has spent some 20+ years tuning rotaries.
Havent heard anything but praise for him, just finished dealing with him as he supplier me with an LT-10s, dash unit and laptop dongle, he seems like a complete legend.
Check out http://www.wgtautodevelopments.co.uk/, think it\'s about £150 for a full tune?

thanks for that;) ,i will be calling to him,had a look true the site there,sounds like he is the man for Microtech,what model car you runing your LT in, dash unit sounds good,thats the hand held controler is it? i have the laptop dongle and software but dare not go near anything, i have the manual for the MT/LT Series aswell,but again i may as well be looking up a ducks ass:3Confused

[grinder]

welcome to MRC

thats a nice car you have there

[sadgoth]

Tim at RX Motors also maps Microtechs and is a registered dealer. The LT software is actually quite easy to use, but if you don\'t have the expertise to know what you are doing buy adjusting the various settings you can do way more harm than good!

[leigh1551]

yes mate, those are the fixed lights I am after, if anyone can point me in the right direction i would be most grateful
 
leigh

[flatout]

yes mate, those are the fixed lights I am after, if anyone can point me in the right direction i would be most grateful
 
leigh

hi ya, the lights are part of the bumper,not cheap at all, you can get lights that replace the standard ones on ebay.com, worth havin a look on www.rotaryart.co.uk

[flatout]

been a bit, here she is just after a full paint job under and over:chat by myself,took 6 weeks to paint and polish,first time painting a car,used 2pac paint,got a load a body parts to put on now,overfenders that a lad on this site put me on to,thanx, i sold the microtech ecu as i cant be doing with pre mixing,i will only blow up my new engine,again,

[Brett]

Looks interesting :yes  When are the wider arches going on? :wave

[dthebuk]

what did you do with the advans!!! they were awesome

[m1tch]

Where did you get the overfenders from?

[Jimi_Hendrix]

Hey man, welcome to the club! I\'m prety new here too, certainly to both turbo and rotary power! Lol! I\'m trying to figure out whether or not i\'ve got that dreaded 4000RPM hesitation at the moment (any pointers on what to look for anyone?).  
 
BTW, do you want to sell the advans? Drop me a little line on fc3s@hotmail.co.uk if you do :Thumbsup!.