Fastest Stock Twins thread

Started by Glenn Butcher, August 24, 2005, 03:36:17 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

M@r]{

Well not exactly \'Stock Twins\' are they?  So to post on this thread you will have to sell (to me) your BNR\'s and put back on (or px with me) some stock ones  :p


Quote from: nicksterrx7Not sure if this is the right thread as I don\'t have an exact speed, but just had my BNR twins mapped by RE:Worx, putting out a healthy 355 RWHP at 1.0bar boost (thats about 410 - 420 fwhp I guess??).  Very pleased.  At 0.8 bar they were doing 316rwhp compared to my old set up that was maxed out at 289rwhp at 0.8 bar boost.  I can certainly feel the difference!

andysmee

but the rules say that uprated stock twins count! so a BNR or other stage 3 uprated turbo is in, isn\'t it?
 
..not that I like it either!

M@r]{

Isnt that a contradiction?  Uprated +Stock?   :D

Seriously though, if any twin turbo \'counts\' why call it the Fastest "Stock" Twins thread?

andysmee

Agreed!
 
...but the rules on this thread are stated clearly enough...
 
Rules

1. Must be a twin-rotary engine. No triple\'s, quads or piston conversions.
2. Must have original twin-turbo\'s, but they can be uprated e.g. enlarged wastegate, 360 degrees thrust bearings.
3. Must be street legal.
4. The driver must be the owner.

All other modifications are allowed e.g. engine porting, uprated boost etc.

Rixio

They are still stock just re-worked to produce more power thats all...;)

gillard28

They only use the manifold of the orignal turbo.

chrisBoid

Quote from: nicksterrx7Not sure if this is the right thread as I don\'t have an exact speed, but just had my BNR twins mapped by RE:Worx, putting out a healthy 355 RWHP at 1.0bar boost (thats about 410 - 420 fwhp I guess??).  Very pleased.  At 0.8 bar they were doing 316rwhp compared to my old set up that was maxed out at 289rwhp at 0.8 bar boost.  I can certainly feel the difference!

Not quite the right thread as this is specificaly about 1/4 mile times.  Post here for some HP chit-chat / feedback.

But if you do run down the strip please post the results here as BNR\'s are technically uprated stock turbos as you do need to supply donor stock turbos to get the BNR\'s made up.

To all : Perhaps we should rename the thread to "Fastest Stock-based Twins thread"?  We want anything based on the stock twins to be allowed but not anything else, e.g. 2 x GT35R\'s etc :)

chrisBoid

Table updated :)
Some great times being posted.

andysmee

Any chance we can extend the table to note what engine porting and turbo uprating (BNR, KS) etc? It would be nice to compare stock for stock and uprated for uprated without excluding anyone from the list.
 
And I want to know what the fastest stock-stock car is!!!

gillard28

Sdminus
 
Full mazda stock spec engine
Stock twin turbos/ 100 000 KM +
Full road tires
Full interior and full weighted car with tool kit spare wheel and half tank of fuel
Apexi power fc tuned by ME
 
60 ft 1.901
330ft 5.151
1/8 mile 7.803
MPH 92.20
1000ft 10.030
1/4 mile 12.015
mph 117.20

Fendamonky

#385
Quote from: \'M@r{;420507\']Well not exactly \'Stock Twins\' are they? So to post on this thread you will have to sell (to me) your BNR\'s and put back on (or px with me) some stock ones :p

The BNR\'s do require a working core in order for Bryan (guy that makes them) to produce them. However the stock Hitachi turbo\'s are replaced with Garrett GT28\'s (the GT28\'s handle the abuse of higher boost much better than stock HT12\'s), among other things.
 
nicksterrx7, what kind of engine porting/support mods do you have to be making 355whp @ 1.0 bar?? I just had my BNR\'s installed, then mapped to 1.1bar by Max and I only managed 325whp (stock ports and greddy SMIC).. then again, my intake temps were 40+ on the dyno (stock IC duct needs to go!!)
 
I\'ll learn to launch then see what kind of times I can pull at Santa Pod ^_^

russellparkerx

I bought my car set up for quarter miles on stock twins, when is the next time I can run it when a few Rex owners will be about?  Anyone know if my car is one of the guys in the chart here?  A3 RXO is the reg plate, Rotechniks built.

BlitzBoy

Here are the dates for next year, they start quite early god knows what the weather be like
http://www.rwyb.co.uk/dates.php
"Piston Killa" 3rd Gen\'94 \'Oldone Racing Full Bridge Ported REW 13b engine with SCR seals\'. HKS T51 KAI turbo BBM mapped Motec ECU

JDS/HKS Street Class Championship Runner up 2011
Rotorstock winner 08,09
http://pistonkilla.blogspot.com/
old spec HB T51 470 @ wheels @ 1.2 BAR, 555 @ fly 10.46 @ 130 @ 1.25 Bar
new spec FB T51 482 @ wheels @ 1.15 BAR, 570 @ fly

New Project
"el fénix" RX2 by Mark & Mark

russellparkerx

Hey all,
 
I have just got my car up to scratch, so I\'m going to RWYB on Sunday the 5th of April.  I\'d love to meet with anyone from MROC who\'s going, especially stock twins peeps to run against.
 
Let me know if you\'re going!

russellparkerx

Gentlemen,
 
I took my FD to Santa Pod yesterday - my first time on the strip.  Best of 2 successful times was a 13.09 at 111mph.  Did a third run and got a red light for slowly rolling over the line - very confident it was my best launch, so disappointed to not have a slip starting with a 12.
 
The 60 ft time was 2.143 seconds, so I hope to make a big improvement to the time on my next outing by refining the launch.
 
Met Blitzboy and Declan (Declasm?) and generally had a superb day.
 
Best wishes