How many horses do you think I will have

Started by strange_days_uk, August 25, 2006, 01:40:11 PM

Previous topic - Next topic

0 Members and 0 Guests are viewing this topic.

Print
Go Down Pages1
User actions

strange_days_uk

August 25, 2006, 01:40:11 PM
My 3rd gen is booked into RE:Worx next month.

Current spec:

Stock twin tub
Apexi intake
Apexi PFC mapped to 0.8 Bar (maxxed injectors)
Racing leads

290 bhp at the rear wheels

To be installed:

850cc primary injectors
044 fuel pump
Greddy FMIC
low temp thermostat
Coolingmist water injection (gonna run 50% methanol, 50 % water mix)
TURN UP BOOST AND REMAP

Whadd y\'all think ??

Me hoping for a good 350 at the wheels.

Closest wins a packet of peanuts.. :yes

Don\'t all shout at once!

Jame5

#1
August 25, 2006, 01:42:57 PM
no idea mate but your avatar is sweet!

kermit

#2
August 25, 2006, 01:57:30 PM Last Edit: August 25, 2006, 02:01:21 PM by kermit
Any porting work on the engine?

I would guess around 320-330 RWHP on stock twins.

You will probably want some better plugs too if you haven\'t already got some!

edit:- I assume you have a larger downpipe and de-cat?

strange_days_uk

#3
August 25, 2006, 02:10:52 PM
Full decat exhaust system, don\'t think any porting has been done.  I would have thought a good 350 with the WI as well.?

kermit

#4
August 25, 2006, 02:43:58 PM
Not sure what effect the WI will have on performance figures, but will help keep the intake temps down along with the FMIC so will be safer running higher boost!

Dont worry about chasing figures anyway, its on the tarmac is where it counts.  As long as you are happy with the improvements and how it perform on the road, then thats what matters!

BlitzBoy

#5
August 25, 2006, 02:44:12 PM
depends what boost you going to run

At 1 bar I reckon 320 atw
"Piston Killa" 3rd Gen\'94 \'Oldone Racing Full Bridge Ported REW 13b engine with SCR seals\'. HKS T51 KAI turbo BBM mapped Motec ECU

JDS/HKS Street Class Championship Runner up 2011
Rotorstock winner 08,09
http://pistonkilla.blogspot.com/
old spec HB T51 470 @ wheels @ 1.2 BAR, 555 @ fly 10.46 @ 130 @ 1.25 Bar
new spec FB T51 482 @ wheels @ 1.15 BAR, 570 @ fly

New Project
"el fénix" RX2 by Mark & Mark

strange_days_uk

#6
August 25, 2006, 02:51:01 PM
Oh well, I guess I\'ve just been :flamed

Huh

I\'m gonna prove you all wrong with my monstrous figures :-)

I\'m off to sulk

Ed_RX7

#7
August 25, 2006, 03:09:14 PM
310-315 me thinks don\'t be upset though thats good power near the 400 fwhp mark...can\'t be bad!!!
Edrx7Parts

07531 669 768

"ALL I HAVE IN THIS WORLD ARE MY BALL'S AND MY WORD......AND I DON'T BREAK \'EM FOR NOBODY"

Official Distributor for TURBONETICS, ROTARYWORKS, ATS/CARBONETICS, SHINE AUTO PROJECTS and XFORCE.
Supplier of HALTECH Ecu\'s and components
Also of

John Yorke

#8
August 25, 2006, 04:16:28 PM
If you are on stock ports dont expect megga numbers, you will be hard pressed to flow much more than 1bar through them so as everyone has said 310ish ATW would be a GOOD SAFE result, I am sure more could be made but the engine is most likely to be a grenade:flamed

PETE SMITH

#9
August 25, 2006, 04:28:50 PM
My small single has just been dyno\'d by Max and made 340 ATW @ 0.9bar-so if you make this or just below with stock twins, i would be smiling!!:Thumbs-up
Print
Go Up Pages1
User actions