Must be doing something right for a change

[NixRX7]

After all the things i have heard about the stock IC getting heatsoaked, and aftermarket filters doing the same i thought i better have a go at a bit of DIY and make up some heat shield / Ducts, especially after coming back yesterday and popping the bonnet and finding the filters/IC/IC piping to hot to touch.

SOOOOOOOO i started looking about for something to use as a heat shield, finding nothing i spied  our old tumble drier, a quick look inside showed a nice shiny drum ready to be cut up and used.

10 mins later i have a nice long length of Stainless Steel, 20 minutes after that and with the aid of a few rivetts and some old trim edge i had a nice shiny heat shield and duct.

Fitted it all in so the filters are protected and fed air from a gap by the rad and the original cold air feed.
The IC i used another piece to help get air up and toward IC.

Took the RX out today for about a 2 hour drive, got home popped the bonnet to see if my handiwork had any effect, i was pleasently surprised to find the IC inlet pipe quite hot, the IC itself only warmish and the IC outlet not hot at all, same with the filters, both nice and cold.

Dunno how much difference to driving it will make, and i doubt i\'ll notice it, but at least its one less thing to worry about and shows i must have done summit right for a change.

[Wav]

Good stuff, sounds like you\'ve definitely done something right

Keep up the good work,

Paul:)

[PETE SMITH]

Well done!
I\'ve always felt that "heat-shielding" was a dedicated DIY job!  :p
I\'ve looked at various odds and ends to use for heat shielding.
Basically "HEAT" is a major part of the RX7 dictionary! ...whether it be shielding or venting, i\'m sure there\'s no perfect answer
Pete

[*Bowsy*]

Nice one fella,ya got any pics of your handywork? :chat

[NixRX7]

Cheers guys, as the old geezer from the A-Team used to say "i love it when a plan comes together"

I\'ll gets some pics up tomorrow, not that you can see a lot with everything back in place.

[Donato]

Fantastic, the girlfriend/wife wants a new tumble dryer, you still get parts for the car!  

[NixRX7]

Yep, never throw anything away, you never know when it might come in handy.

Heres the pic of the heatshield, cant get one of the duct, cuz its buried under all the other bits.

The other bits just arrived form USA and i still have to fit them at some point

[dandan]

is that blue piston a bonnet lifter? or a really small susp strut? brace?

[memski]

Looks like a torque brace to hold the engine steady and help eliminate mis-shifting up to 3rd  :god

[NixRX7]

Yup its a torque brace for the engine, got the pulleys,belt and the torque dampner from the states, cost just over £100 delivered for the lot.
All fitted now, looks much nicer without the air pump.

[Tintin]

Good work , heat sheilding looks good

My heat shield is presently work in progress at the moment , removing air pump is on the to do list , how hard was it to get the old pulleys off

Also seems a good price for the gear where did you get it

[NixRX7]

The water pump pulley is easy, just the four bolts, the alternator is the real git, you need an air impact rachet to remove it, normal spanner wont do, as they are on really tight.

I got all the bits from Ebay USA the link to the guys store is http://motors.search.ebay.com/_W0QQsassZccis99

Everything is well packed and fitted very well.

HTH

Nick

[Tintin]

So have you got your own air compressor or did you get a garage to do it

[NixRX7]

heres a pic of the pulleys and torque dampner fitted.

[NixRX7]

I got a mate to do it, took 15 seconds to get it loose, then stuck the new pulley wheel on and used the air ratchet to do it up again.
Best bet if you dont know any one with a compressor is take the alternator to a garage and get them to do it for you, doubt they will charge you much, if anything at all.