Messages

As title really , fancy a new project for 2015 and the urge to get a rx7 is back . I'm located in bournemouth so closer the better . Don't fancy travelling to Scotland for a shell .

Wow thats one of the best looking rx7\'s i\'ve ever seen

Sorted was the TRS Relay , Had got some water in it :xconfused
 
Anyway the ghost has gone ... YAY

My sidelights wont turn off , every time i turn them off 5 seconds later some times more , some times less they turn back on :xconfused they flicker some off the time , Anyone had anything like this before or do i have a haunted car :Thumbsup!

My rad from WGT(i believe its a radtec) has two fans on the back with a 2 wires coming from each of the fans with a connector on the end , Presume ones a feed and ones ground . But the old wires that went into the standard rads had 4 wires going in , which ones do i use Just the feed and ground What controls the fans then ??
 
Cheers
 
Stevey

What website do people use to look through Yahoo japan auctions
 
I cant find a good website

Don\'t know how you managed it, they said I have to be over 23.

Im not sure tbh , I think its because ive been them for 3 years and the car before the fd was a 350bhp 200sx S14a + Ive got 4 years no claims and a clean lisence , Its garaged and in a good area too . I think it all helps
 
Hope you sort something out

Im 22 with a 93 red fd3s with basic mods , With sky insurance and paying 1100 fully comp
 
I dont see why they wont quote you . I got this insurance in November

I know there was a thread on Intercoolers called Vmount or FMIC but i cant find it anywhere :confused:
 
What are the advantages of both choices and where can you get them ?? I cant find anywhere but Ebay but im always worried about ebay stuff
 
Any help would be great

Has the car been fitted with an Apexi ecu? has it been mapped? general opinion i believe is to fit a decat pipe air filters etc , only when the car has an Apexi that can be mapped, it sounds as though this problem started after you fitted the decat pipe! what did you did you do with the cat sensor wires? (under drivers seat) is the heat light on? the knoking might be to do with the decat pipe if it\'s only just started!
Is yours the black FD? reg- RX1 *** that i saw near hurn the other day?
Bob

I just tucked the sensor to one side , No heat light came up . Just what someone told me to do
 
 
Yeah a guy called chris told me about the need for a Apexi ECU , Its only been driven to get around as little boost use as possible . I thought that would be OK , Will it :xconfused . If not ill just leave it in the drive
 
But it seems to be running really rich , always popping and banging on idle and normal driving . Rotor engines confuse me
 
No mines a Red one dont know any black ones with that plate

Owned my rx7 for around 1 week and a half and its been brillant , But after fitting a decat pipe instead of a cat i\'ve had a intermittant fault . I did a 100 mile round trip on the way there it was its normal self , But on the way back i noticed a knock every time you used the brakes , Didnt think much of it . Assumed it was the exhaust being abit loose , Checked undernearth when i got home and its all connected OK and theres no sign of any parts of it knocking on anything.
 
To top it off when i started it earlier the whole car was shaking on idle , The gearknob was all over the brake and it was vibrating down the steering wheel etc etc. But was fine when i moved it back into the drive  only when its idling does it do it . But not everytime you drive it infact its only done it once or twice and it feels unsafe.
 
Its pretty much standard except for a cat back blitz, straight tho midpipe and some Koni adjustable shocks.
 
 
The car had a rebuild at Hayward Rotary about 2 and a half years ago and has only covered 8000 miles so i hope its not serious :mad:
 
Any help would be great

Thanks for all your help, got some from driftworks
 
Thanks again
 
Stevey

Just looked on the driftworks site , but im a little confused what is the normal Rx7 size they have nissan etc and toyota and ford etc listed but no mazda
 
Help :3Confused

Random i know , But ive only just got my rx7 and i was hoping to fit my 18" Buddy club p1 sf\'s but the standard nuts are to tight and the nuts i got off my 200sx are the wrong thread.
 
Wheres a good place to get nuts from ?? i want some slimline ones
 
i saw these but ebay scares me :Giggle
 
http://cgi.ebay.co.uk/Mazda-slim-alloy-wheel-nuts-Mx3-Mx5-Rx7-121-323-set-20_W0QQitemZ290260851678QQcmdZViewItem?hash=item290260851678&_trkparms=72%3A12%7C39%3A1%7C66%3A2%7C65%3A12%7C240%3A1318&_trksid=p3286.c0.m14
 
Also ive always used spigot rings and i was gonna get some to fit the rx7 but people keep telling me not to bother makes no difference is this true ?
 
Thanks in advance
 
Stevey

Thanks for the info , been brillant :Thumbs-up