Wayne's boosted 8 project

[Mr Spiller]

Nope it’s gone , nowt in there
I don’t , well did t have a torque wrench so when tightened Spanner  tight    I’d always stick a spanner and slap it with a rubber mallet a few times .
Done it for years .......



Sent from my iPhone using Tapatalk

[Mr Spiller]

Blimey Wayne you got loads of bits!!!

Sent from my SM-N950F using Tapatalk

Yep none to get me further than this



Sent from my iPhone using Tapatalk

[boosted]

Loom injectors..brap brap...
If your following clives build rx8 loom..electric throttle. Rx8 pcm with a piggy back adaptronic for boost...nice throttle control and idle. Rx8 dash will work then etc...
Thats how id do it!

Sent from my SM-N950F using Tapatalk

[Mr Spiller]

Loom injectors..brap brap...
If your following clives build rx8 loom..electric throttle. Rx8 pcm with a piggy back adaptronic for boost...nice throttle control and idle. Rx8 dash will work then etc...
Thats how id do it!

Sent from my SM-N950F using Tapatalk

Loom - got 2 of them
injectors - just primary so far
brap brap...ha ha
If your following clives build - unless there’s another way to do it ?
rx8 loom..electric throttle. - this is where I’ll need to learn a lot of using the RX8 throttle body
Rx8 pcm with a piggy back adaptronic for boost...- I have the new modular one so will need to find out what special stuff that can do compared to the piggy back one
nice throttle control and idle. Rx8 dash will work then etc...
Thats how id do it!- just like that lol


Sent from my iPhone using Tapatalk

[Mr Spiller]

Done my final bit of aero on my track car before I get the other one up to start the swap
Diffuser - took about 60 hours in total
20 of them was me getting up and down from the floor . If this virus doesn’t kill the economy I’ll be lifting my garage roof 3 foot to fit a 2 poster




Sent from my iPhone using Tapatalk

[Mr Spiller]

Looking at some photography from the last track day I done it seems I have bent the front splitter up in the middle whilst loading it on the trailer

If you zoom in it’s pretty clear
Whipped the bumper off and found the culprit - a bent metal hanger
Time to invest in some caravan ramps to put under the rear wheels of the van to make the loading angle of the trailer better .
It’ll be touch and go weather I need to trim the back of the diffuser slightly too
Got a car to strip in next few days then it’ll be time to start the build
Can’t wait , but also am feeling quite nervous as I don’t know a lot yet . reading about it is one thing - putting it together - totally different


Sent from my iPhone using Tapatalk

[Jamie R]

Christ you did well in 60 hours, you should come work for me lol.

Looks impressive, I’d be interested to know if all the mods have made a noticeable difference


Sent from my iPhone using Tapatalk

[Mr Spiller]

Christ you did well in 60 hours, you should come work for me lol.

Looks impressive, I’d be interested to know if all the mods have made a noticeable difference


Sent from my iPhone using Tapatalk

The wing and splitter did
Could be waiting a while to test the diffuser tho ........


Sent from my iPhone using Tapatalk

[Mr Spiller]

Donor car is in
I’m currently on half days in work so got stuck in earlier
4 hours and it’s out
No idea what I’m doing next  but I’m optimistic


Sent from my iPhone using Tapatalk

[Jamie R]

Impressive garage mr spiller 

[Mr Spiller]

Impressive garage mr spiller 

Thanks Jamie it’s a tip
Raining  next  few days so a good clean , clean shed and dump all the shite in there


Sent from my iPhone using Tapatalk

[Jamie R]

Lol if that's a tip don't venture into mine, constantly looks like a flour factory

[Casey]

Lovely big, open space though 

[Grant Monkhouse]

Are you using the stock FD twin turbos on this project?

Sent from my VOG-L09 using Tapatalk

[Mr Spiller]

Lol if that's a tip don't venture into mine, constantly looks like a flour factory

yep I bet it does
More like a Columbia’n garden centre


Sent from my iPhone using Tapatalk