FS: Mazda RX7 FC3S

[L18M]

Dont really want to post this but i really don\'t have any time or space for this any more.

JDM S5 with chassis covering about 75000 miles.
I think its pretty good condition for age and underside looks pretty good.
Not spotted any obvious signs of rusting.
Brought in 2007 and personally covered about 3000 miles in uk and not used in winter.

Engine rebuilt By MAV tuning (Ben Lewis Mav on here) just over a year ago and done about 500 miles running in. Just rack up a few more miles then can go for mapping. Expect about 375bhp (fly, give or take 25bhp) at about .9 bar (rough estimate).

Resale values of after market parts alone (priced to sell) is well over £6k, not inc chassis, body and oem parts.
That gives you a bit of an indication to how much i\'ve put into her.

I don\'t expect to see this price but serious offers only.
Please don\'t bash this post about it not being worth £xxx etc as different people see things differently.

Bad points:
Exhaust needs a good clean out as oil built up from when the turbo oil seal went.
I think there is one leaky injector on top rail. Possibly cracked fuel feed line going to injector (not had time to investigate fully yet)
Needs a good clean on outside.

Thats the only things i can think of then ready to put through MOT. Has TAX til July 2014.

The engine is strong and starts 1st time, as expected from being freshly rebuilt.

I\'m sure there\'s more but i cant think of anything else for now.
Please feel free to ask any questions.

PS will not break the car as no time or space.

Spec list:

Intake / Exhaust:
HKS Green mushroom filter
HKS Super Sequential BOV
Custom V-mount (twin slim rad fans)
FD rad
Air pump, AFC & Split air deleted
HKS Manifold
3" Down pipe & "silenced" mid pipe
Screamer pipe
Kakimoto Exhaust

Engine:
Greddy compression tube
Rebuilt block (MAV tuning) covered 500 miles
FD corner seal springs
New Apex Tips
Pineapple racing HD water seals
T35 similar spec tub rebuilt w/ 360 thrust bearings and new oil seal
Greddy wastegate
GM 3 Bar MAP sensor
1680cc Bosch secondary injectors
SARD FPR w/gauge
Bosch 044 fuel pump
Twin Alt Pulley
Magnecore HT Leads
A/C deleted

Brakes:
Cusco BMC stopper
Groved brakes

Electronics:
Greddy Profec B spec II
AP Eng PFC & commander
Banzai Racing Harness
Beam Boy 8k HID
Earthing kit

Chassis / Transmission:
RE雨宮 coilovers (Height and dampening adjustable & adjustable top mounts)
Cusco front strut
Cusco rear strut
Feed \'B\' Pillar strut
Exidy organic clutch
Braided clutch lines
Yoko parada fronts
Toyo T1R rears
Yoko SA3R 17" 8j 9j
LSD (unknown, locks pretty quickly)

Interior:
RE雨宮 Steering wheel
Knight Sport Speedo in kmph
Greddy  boost gauge
Short shift
Razo knob
Battery relocated to rear bin
Replace rear seats with bins
Efini III fixed bucket seats
Red flocked cluster surround
Red flocked front console
Carbon Fibre look instrument cluster face

Exterior:
Anniversary Racing Factory Aero wing mirrors
Corksport lip spoiler
RE雨宮 Side step (shine auto)
Attain Vented o/s headlight cover
VIS Racing Carbon Fibre hood
CFl look small gay wing
Respray white
RE雨宮 Rear spats
No sunroof (OEM)

[L18M]

Pics

[grinder]

looks a beast good luck with the sale !!

[mick choi]

hi m8 if ever u do break ur fc :   i would like the carbon bonnet, feed b pillar bar, efini bucket seat  cheers mick 07894 707535

[chrisJDM]

I\'ve not been on here for a long long time, didnt expect to see this!!!! :2eek

[AndyGen3]

Any better pics of bodywork ? Also any of engine bay ?

And guideline price please

[AndyGen3]

Also pics of underneath if possible !

Cheers

[tuner017]

sucks that you have to sell mate.  i finally dug out those indicators if you decide you want to keep it.  good luck with the sale though.

[chrisckyu]

whats the price

[basch32]

Like above can you pm me a price and also any additional pics of engine bay/underneath etc.

Thanks

[L18M]

hi, sorry guys been away and just got back.
can you drop me your emails so i can send you guys pics and prices etc.

rex7parts (at) google mail (dot) com [no spaces]

thanks

[L18M]

Any better pics of bodywork ? Also any of engine bay ?

And guideline price please

body work is good shape, bit dirty and needs a good wash and scrub.
only major bad point is the dent above the filler slap in the above pic.

drop me your email and i\'ll get more pics to you.

[L18M]

sucks that you have to sell mate.  i finally dug out those indicators if you decide you want to keep it.  good luck with the sale though.

better late than never hehe
how much for the indicators? if dont sell then will become a long term project :Giggle

[L18M]

I\'ve not been on here for a long long time, didnt expect to see this!!!! :2eek

sad times.. changing times.. but some girl should be happy i\'d swap carbon build up in engine for a rock made of carbon.
If only the carbon build up in rotaries turned into diamonds :Giggle

[Grant Monkhouse]

I don\'t know if its me but where\'s the asking price?? Generally helps with selling something