help fd3 will not start up

[gavinnblake]

hello all need help
my rx7 will not start up:Grrr
 
1996 Mazda RX7 Type R Single Turbo T88 34D Rotary Engine 13B
 
i have look at Spark Plug Clean them up and car batter and the yellow fuse no look dont no what to do :confused:
 
i do think it will be the abs wheel sensors or not plug in as my wire has snapped off :confused:

made a video
 
http://s238.photobucket.com/albums/ff309/gavinnblake/?action=view¤t=IMG_0348.mp4

[TRIND-FD]

Loving  your car Gavin especially the gauges.

I would say flooded.  New plugs . Or check clutch switch.
If it was fine, then never started.  Deflood and new plugs.

[m1tch]

Guessing flooded, pull the EGI fuse, press the throttle fully down, crank it a few times, put the EGI fuse back in and try it again (without opening the throttle), then report back.

[gavinnblake]

Loving your car Gavin especially the gauges.
 
I would say flooded. New plugs . Or check clutch switch.
If it was fine, then never started. Deflood and new plugs.

 
hahaha got a gauges just wouking on out in the sun
 
yes it looks like it need new plugs
 
thanks alot

[TRIND-FD]

hahaha got a gauges just wouking on out in the sun
 
yes it looks like it need new plugs
 
thanks alot

Check your fuses where the egi fuse is too mate.

Bloody rare as hens teeth them gauges, aswell as their intercoolers etc

[gavinnblake]

well got new plugs in now and it start up but this happening now
 
http://s238.photobucket.com/albums/ff309/gavinnblake/?action=view¤t=IMG_0350.mp4
 
Any help would be great, thanks.

[TRIND-FD]

Have you knocked the map sensor pipe off. Map sensor is on the bulk head passenger side.
Plug leads on the right way.

[gavinnblake]

Have you knocked the map sensor pipe off. Map sensor is on the bulk head passenger side.
Plug leads on the right way.

mmmm not that all check
 
had pip on phone from WGT Auto Developments Ltd he said its a wire falt

[Indian]

make sure you have your plug wires going to the correct spark plugs. Also, where are you getting your rpm signal from ? Looks like you need a better ground.

Are you using a stand alone?

[gavinnblake]

do you no what Compression Tester us on this Test
http://www.youtube.com/watch?v=s3qjrR4aq7Q&feature=BFa&list=FLTr5t8jqT5etAIKvyamjbTw
as am looking for one to buy but dont no which one on to get on ebay am using this one on my rx7 but corned get it to go up & down on psi so can do 1-2-3 Rotary test      

this on my rx7 F Rotary test on a cool Engine
http://s238.photobucket.com/albums/ff309/gavinnblake/?action=view¤t=IMG_0422.mp4

R Rotary test on a cool Engine
http://s238.photobucket.com/albums/ff309/gavinnblake/?action=view¤t=IMG_0415.mp4
 
help would be great, thanks

[TRIND-FD]

If you hold in the pressure release button while you carry out the test it should bounce.  Or if you can remove the valve and put a bolt in it.

[TRIND-FD]

Emailed you a link Gavin , I have one the same, you can reMove the valve and put your finger over the hole.

[gavinnblake]

Emailed you a link Gavin , I have one the same, you can reMove the valve and put your finger over the hole.

THANKS TRIND-FD got your email i bought one good price as well

[gavinnblake]

Emailed you a link Gavin , I have one the same, you can reMove the valve and put your finger over the hole.

hi i have the Compression Tester in post today there 2 valve 1 in the pip and 1 in the gauge do i take them both out and put a bolt in the gauge one
 
and on the bump test & Compression Test do you no what psi i shud get
 
thanks alot :guinness

[TRIND-FD]

hi i have the Compression Tester in post today there 2 valve 1 in the pip and 1 in the gauge do i take them both out and put a bolt in the gauge one
 
and on the bump test & Compression Test do you no what psi i shud get
 
thanks alot :guinness

Will go look at my old school tester now lol, iirc 100 psi plus , . But it\'s not 100% accurate . But a good indicator