A single is conceived, few month before she is born?

123tom123tom · February 09, 2012, 03:02:23 PM

Quote from: 123tom123tom;811621just rang WGT just to confirm my mapping for tomorrow morning I asked for the price, they said Â£350, does that sound right or not, he ask me if it was a fresh engine etc have said the wrong thing??? I was told it would be more round the Â£200 mark

also forgot to add, I haven\'t plumbed a DumpValve into my system? this wont have any effect on mapping tomorrow will it??? :o as you can probably tell I am still freting a bit

Grant Monkhouse · February 09, 2012, 03:02:26 PM

350 is right, he will start from scratch basically and when you drive it away you will be amazed at the difference.

If you need it tweaking after Installing some new bits on the car he will charge an hourly rate to give you the benefits of those upgrades.

Grant Monkhouse · February 09, 2012, 03:04:53 PM

A lot of people don\'t run dump valves anyway, I\'m not going to be running one on my turbo setup but I do have a ported shroud inlet housing on my turbo, which helps a bit

Pip will be able to advise you on if you need one or not, but I\'m guessing no.

123tom123tom · February 09, 2012, 03:12:57 PM

might not be to everyones taste but I think it looks quite good??? plus it has a actual purpose of keeping the air flow tight to the rad

123tom123tom · February 09, 2012, 03:19:19 PM

sorry about pic quality, it was poor lighting and phone pic

123tom123tom · February 09, 2012, 03:21:36 PM

Quote from: Grant Monkhouse;811629A lot of people don\'t run dump valves anyway, I\'m not going to be running one on my turbo setup but I do have a ported shroud inlet housing on my turbo, which helps a bit

Pip will be able to advise you on if you need one or not, but I\'m guessing no.

cheers, thanks for the advice :Thumbsup!

stylus350 · February 09, 2012, 03:33:41 PM

All good ducting is a good thing! Dump valves are pointless.

Grant Monkhouse · February 09, 2012, 03:50:29 PM

Ducting looks good!

123tom123tom · February 09, 2012, 03:58:30 PM

Quote from: Grant Monkhouse;811642Ducting looks good!

cheers, made it myself, was well chuffed with the way it turned out. also made the turbo shield for the heat as my bonnet was getting extremely hot

Grant Monkhouse · February 09, 2012, 04:18:07 PM

The only way I would run a dump valve is if I had a really big turbo and a none ported shroud housing.

123tom123tom · February 09, 2012, 04:27:07 PM

Quote from: Grant Monkhouse;811649The only way I would run a dump valve is if I had a really big turbo and a none ported shroud housing.

is mine too big (t70) lol and it doesn\'t have port shrouding either

oh no!! it does compressor surge a little and I haven\'t even run it on boost because it isn\'t mapped of course

shaunwil · February 09, 2012, 05:18:10 PM

You will be fine ! Pip will tell you if there is any issues.

Its looking very nice, hope you enjoy the mapping experience

Shaun

Grant Monkhouse · February 09, 2012, 05:39:38 PM

T70 isn\'t big, I mean gt42, borgwarner 472 etc

123tom123tom · February 09, 2012, 08:15:18 PM

Quote from: Grant Monkhouse;811663T70 isn\'t big, I mean gt42, borgwarner 472 etc

i know it aint that big but still quite big??

Grant Monkhouse · February 09, 2012, 08:31:42 PM

It\'s big enough. It my meaning of big may be different to yours