Turbos

[jetpilot]

Hi guys, not that clued up on turbos so looking for a little advsie. I think my T78 has seen better days so looking to change. I like the sound of a T04Z, i think it would suit my requirements well, im not looking for Huuggee power, just something that boosts from low down and will give a nice top end hp figure. However, is there a modern quivalent of the T04Z? :driving

[Mazdarotaryparts]

Hi Jon,

The T04Z is a very good "modern" ball bearing Turbo and your exactly right with what you expect it to give you ,

If your interested we can supply you a genuine one for £1150 plus Vat

hope this helps

[jetpilot]

Well there you go, i told you i didnt know much about turbos, i thought it was older technology, lol.  Whist once again maybe sounding daft, if i buy new, is there a limited warranty on failure? Is the T04Z happy with above 1 bar of boost?

[Speedline Imports]

TO4Z is a very good all round turbo and easily copes with over 1bar boost.  Speak with Blitzboy, he was running this turbo for a while.

[Mazdarotaryparts]

Well there you go, i told you i didnt know much about turbos, i thought it was older technology, lol.  Whist once again maybe sounding daft, if i buy new, is there a limited warranty on failure? Is the T04Z happy with above 1 bar of boost?

As none of us with Rotarys ever run anywhere near the boost capabilaties of any of these Turbo\'s yes it\'s O/K,

If it was a Piston engine then it may be expected to perform with many bar of boost pressure but as none of us with Rotarys ever run anywhere near the boost capabilaties of any of these Turbo\'s yes it\'s O/K,

As for warrenty,

As with anything, if it\'s the fault of the product in a short space of time then yes it\'s covered, however if it\'s due to a new Turbo not being primed with oil before initial start up and running dry or bits of engine hurtling through it, then no.

After fitting many Turbos to many things over the years 99% of the time I have found failure is normaly one or the other unless the thing has done like 150k plus and simply worn out ,

[jetpilot]

Thanks Clive, a great help as always. Once i have had the final verdict on mine i shall get in touch. Ideally i would prefer a second hand unit as i havent really got that to budget, but i do like the sound of buying new, comon euro millions..............

[colin777]

i hear the gt35r is good

[BlitzBoy]

Jetpilot as requested here is the link to my graph half way down the page of my old TO4Z

http://www.mazdarotaryclub.com/forums/showthread.php?t=5273&page=12

[jetpilot]

Thanks buddy, i presume that was flywheel hp, what was the rest of your set up like, fuelling etc?

[BlitzBoy]

hahahahah REAR WHEEL HORSEPOWER BABY!!!!!! yehhaaaaa 530 at the fly

[BlitzBoy]

it was using the Apexi BNR32 pump for the dyno run then I went twin bosh 044 afterwards, 550 primaries, 1680 secondaries

[jetpilot]

i hear the gt35r is good

Tell me more :Laugh

[jetpilot]

hahahahah REAR WHEEL HORSEPOWER BABY!!!!!! yehhaaaaa 530 at the fly

Thats more than im getting out my tractor turbo, lol. Running a very similar set up, what sort of porting did the engine have and are all t04z\'s the same? Sorry, thats the last question.

[silverrexman]

As none of us with Rotarys ever run anywhere near the boost capabilaties of any of these Turbo\'s yes it\'s O/K,

If it was a Piston engine then it may be expected to perform with many bar of boost pressure but as none of us with Rotarys ever run anywhere near the boost capabilaties of any of these Turbo\'s yes it\'s O/K,



:Snoring pussys

[m1tch]

nuff said