got bored in work....made some bling

[deanflowers]

I havent got PMs so if you email me i will send my details in the reply, i can do the toytota no problem if you send a drawing, will put the toyota logo on the top for you no problem.

[nikp]

Hi mate - i\'ve measured my caps. The dimensions i have for them is as follows:

Brake Reservoir Cap - Width: 53mm, Depth: 14mm
Power Steering Reservoir Cap - Width: 44mm, Depth: 18mm

All measurements give or take about 1mm. Sound about right to you?

[deanflowers]

that what i thought the replacement brake cap i have from mazda is 18mm deep, i will make them for 14mm deep no problem

 ive got asp to measure his with a vernier for me so we should be right now

[nikp]

Vernier calipers are probably better: I only used a tape measure!! :p

[asp]

once uv made 1 send it down so we can c if it fits proply

[deanflowers]

what to see if you know how to use a vernier dont you mean :chat

[asp]

i hope i can use it,i used that 1 when i rebuilt my engine :rollin

[Jame5]

No point testing these caps on a car with no engine, I\'ll test them.  

[asp]

hmm it has an engine,
its just not where it should be

[Newera]

I havent got PMs so if you email me i will send my details in the reply, i can do the toytota no problem if you send a drawing, will put the toyota logo on the top for you no problem.

I\'m up for 2 pairs for RX-7\'s. Unfortunately I won\'t have my Corolla for a few days, as it\'s away getting some work done.. When I get the Corolla back, I\'ll measure up the caps.

I guess it might be possible to put on the "N" for the Newera Logo? That would look cool, I guess. Better than "Toyota\'s" Logo!

BTW, how many grub screws will you use? Can we have 3 or 4?

Cheers

Miguel

[Newera]

BTW, what\'s your e-mail address, please?

Miguel

[deanflowers]

deanflowers2000@yahoo.co.uk

sorry

[Laeeq]

I will have set too please..with efini logo.

will send you the cheque out tomorrow.  When will they be ready?  and i assume all cap sizes are the same or do you need my measurments?

Cheers

[deanflowers]

all power steering ones are the same, and 99% of brake ones are too, most brake caps look exactly the same as the power steering one, but some look different and are deeper, i have measurements for both, the most common one is 14mm deep the other is 18mm deep.

Iam fitting them in as and when at the moment, ive only managed to do 3 top halves this morning of the brake caps so i\'m afraid you will have to bare with me, i will intially make 10 sets then another 10 sets which will save me having to set the machine up continuously, i have been asked for about 8 or 9 so far.

it will probably be a couple of weeks at this rate but hope to speed things up


list

nikp - 1 BRAKE CAP COVER (EFINI), 1 POWER STEERING CAP COVER (EFINI)
jono fd3 - 1 BRAKE CAP COVER (EFINI), 1 POWER STEERING CAP COVER (EFINI)
Ada7 - 1 BRAKE CAP COVER (EFINI), 1 POWER STEERING CAP COVER (EFINI)
Newera -- 2 BRAKE CAP COVER (EFINI), 2 POWER STEERING CAP COVER (EFINI)
ASP -   2 BRAKE CAP (EFINI), 2 POWER STEERING CAP COVER (EFINI)
LAEEQ - 2 BRAKE CAP (EFINI), 2 POWER STEERING CAP COVER (EFINI)

[Fish]

So with all these orders that you are taking, are you going to become a vendor? Or even a member for that matter.

Fish