929 with 12a on ebay

[SSScoupe]

Aha! that would have been me then, was a lhd renault 25 so you\'re not far off! I\'d like to know what became of that 929

My memory\'s not too bad then! Me too... i think it did appear for sale again a couple of years back with some rust bubbles appearing here and there!

[harmeetjohal]

hi all me again with other question...
 
had issues with my clutch, have changed that and the slave, but still nothing behind the pedal...
could it be the master?
 

 
i disconnected the pipe on the right and pressed the clutch but had nothing come out....
 
is it a matter of just unbolting and replacing?
 
is so anyone have a spare or direct me to somone who may?
 
would it be best to look for a rx7 part?

[Rivalrx]

I got a 929 new old stock one off ebay for £17. Keep your eyes peeled. Coming to think of it, I THINK that I have a clutch master (or slave - need to check) rebuild kit that may be of interest??

Maybe take the clutch master off and take it apart - give it a good clean

[clive]

hi all me again with other question...
 
had issues with my clutch, have changed that and the slave, but still nothing behind the pedal...
could it be the master?
 

 
i disconnected the pipe on the right and pressed the clutch but had nothing come out....
 
is it a matter of just unbolting and replacing?
 
is so anyone have a spare or direct me to somone who may?
 
would it be best to look for a rx7 part?

I have found my good S/H master I told you about and if you give me your address I will send it out FOC tomorrow

[harmeetjohal]

I have found my good S/H master I told you about and if you give me your address I will send it out FOC tomorrow

your a star
 
harmeet johal
174 Stoke poges lane
slough
berkshire
SL1 3LH
 
if you can email me your paypal/bank details and how much i owe you that would be great
 
hjohal@rim.com
 
thanks again

[harmeetjohal]

I have found my good S/H master I told you about and if you give me your address I will send it out FOC tomorrow

a Big thank you to Clive at mazdarotaryparts.com a very nice chap who helped with obtaining the part :cheers
 
but i am still not getting much under my peddle, what else can i do?
i have now changed the master, the salve and the cluch :xconfused:eek
 
i can see everthing moving as it should in the engine bay when they clutch is pressed but just dont seem to have any pressure... any ideas?
 
thanks

[shaunwil]

Are you sure the clutch actuator (what is connected to the slave) isn\'t bent ? Can happen on the FD with a stiffer clutch.

Keep Bleeding the system, could still have some air in there getting in the way.

Shaun

[harmeetjohal]

Cheers mate is it a matter of just undoing the \'screw\' on the slave and pumping the clutch?  did this for about 15 min... lost lots of fluid but still not much else

[RobMatthews]

bleed the clutch the same way as brakes

undo the bleed nipple a little have someone press the clutch down and hold, do the nipple back up release the clutch peddle and repeat

[SSScoupe]

http://www.ebay.co.uk/itm/1975-MAZDA-929-RX4-running-RX7-engine-/270955093965?pt=Automobiles_UK&hash=item3f162e9fcd#ht_710wt_1344

back on the bay....

No pics of the rear... i wonder if it ever got a rear valence?  The one i offered is still in my shed!  Hopefully one was found in the uk!

[RobMatthews]

http://www.ebay.co.uk/itm/1975-MAZDA-929-RX4-running-RX7-engine-/270955093965?pt=Automobiles_UK&hash=item3f162e9fcd#ht_710wt_1344

back on the bay....

No pics of the rear... i wonder if it ever got a rear valence?  The one i offered is still in my shed!  Hopefully one was found in the uk!

What do you mean by rear valence? as in the garnish around the rear lights? Im after a good one...

[SSScoupe]

yeah the garnish... i have spare, but its exactly that, a spare as i put the good one on my car.  It has some dents etc and is missing some clips, but when they are hard to find i took what i could get!  I was just lucky finding a better one with an original \'rotary engine\' badge on!

My spare is worth about $75, and a good one can fetch $200, with a mint one going for alot more...

Thankfully RX4 parts have not yet reached rx3 prices yet!!