Clutch problem

Started by Morrmat, April 02, 2009, 04:54:39 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Morrmat

My clutch seems to stick to the floor of my car, it used to occur very rarely, but it now happens every time i drive the car!!

Does anyone have any ideas as to what it is?

BlitzBoy

Clutch Master or Slave cylinder , the seals perish over time and the springs sometimes loose their tension
"Piston Killa" 3rd Gen\'94 \'Oldone Racing Full Bridge Ported REW 13b engine with SCR seals\'. HKS T51 KAI turbo BBM mapped Motec ECU

JDS/HKS Street Class Championship Runner up 2011
Rotorstock winner 08,09
http://pistonkilla.blogspot.com/
old spec HB T51 470 @ wheels @ 1.2 BAR, 555 @ fly 10.46 @ 130 @ 1.25 Bar
new spec FB T51 482 @ wheels @ 1.15 BAR, 570 @ fly

New Project
"el fénix" RX2 by Mark & Mark

Bobbit

Master or slave cylinder fault im guessing, one of the seal will have gone so instead of working the clutch it will just leak fluid.
:Laugh LOL


                                       

Bobbit

:Laugh LOL


                                       

Morrmat

how would i tell which one it is? Are they hard to replace?

BlitzBoy

you dont lol you need to take them both off and check em, the slave is quite easy to take off, the master is bit of pig as you have to get into the drivers footwell and have bendy arms to undo the nuts and disconnect the rod lol
but its not technically hard
"Piston Killa" 3rd Gen\'94 \'Oldone Racing Full Bridge Ported REW 13b engine with SCR seals\'. HKS T51 KAI turbo BBM mapped Motec ECU

JDS/HKS Street Class Championship Runner up 2011
Rotorstock winner 08,09
http://pistonkilla.blogspot.com/
old spec HB T51 470 @ wheels @ 1.2 BAR, 555 @ fly 10.46 @ 130 @ 1.25 Bar
new spec FB T51 482 @ wheels @ 1.15 BAR, 570 @ fly

New Project
"el fénix" RX2 by Mark & Mark

Morrmat

nice one, cheers.  Is there a "how to" for this that you know of?

BlitzBoy

I just downloaded the workshop manual pdf for the FD
"Piston Killa" 3rd Gen\'94 \'Oldone Racing Full Bridge Ported REW 13b engine with SCR seals\'. HKS T51 KAI turbo BBM mapped Motec ECU

JDS/HKS Street Class Championship Runner up 2011
Rotorstock winner 08,09
http://pistonkilla.blogspot.com/
old spec HB T51 470 @ wheels @ 1.2 BAR, 555 @ fly 10.46 @ 130 @ 1.25 Bar
new spec FB T51 482 @ wheels @ 1.15 BAR, 570 @ fly

New Project
"el fénix" RX2 by Mark & Mark

steve garbutt

Check the clutch flexi pipe at the back of the engine as well, i used to have a very minor leak on my car that only very occasionally left my clutch on the floor, it gradually got worse till it popped and left me stranded.
Tact is the knack of making a point without making an enemy.
Steve@mazdarotaryclub.com


BlitzBoy

"Piston Killa" 3rd Gen\'94 \'Oldone Racing Full Bridge Ported REW 13b engine with SCR seals\'. HKS T51 KAI turbo BBM mapped Motec ECU

JDS/HKS Street Class Championship Runner up 2011
Rotorstock winner 08,09
http://pistonkilla.blogspot.com/
old spec HB T51 470 @ wheels @ 1.2 BAR, 555 @ fly 10.46 @ 130 @ 1.25 Bar
new spec FB T51 482 @ wheels @ 1.15 BAR, 570 @ fly

New Project
"el fénix" RX2 by Mark & Mark