finally got my rex !

Started by Shaq, August 21, 2003, 09:00:10 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Shaq

I finally picked up my rx-7 last night I am well impressed with the car you get so much attention driving around in it!     :)

Only thing is when I am in second and put my foot down it doesn’t really seem to shift as fast from 4,500 rpm upwards but under that it pull s like anything??   :confused:


Any suggestions please???


Thanks

Shaq
12.7 on stock twins @ 1 bar (i reckon i can do better!)

Fish

Get yourself a boost gauge fitted. This will indicate if there is a boost problem.

It could be a blocked cat, this can make it feel flat above 4000 rpm.

Dan

mr_tim

What boost gauge do you use/recommend?

There seems to be mechanical, electric, electric with replay and peak functions...

Shaq

fish,

It has got a boost guage fitted i will check the boost tonight, but it pulls good in between 1,500 rmp - 4,000 rmp after that it feels it dosen t have the kick anymore but as soon as you shift into 3 ed starts pulling hard !

Any ideas ?
12.7 on stock twins @ 1 bar (i reckon i can do better!)

Fish

Just a normal mechanical is good enough, you just need to check the boost is ok.

Boost pattern should be 10-8-10 on the earlier models, then 12-10-12 for the post 98 models.

If its less than around 6psi on the cross over point (10-8-10) then it has trouble moving the solenoids.

Dan

Shaq

Fish,

Sorry to sound like a spaz but what do you mean by 10-8-10 boost pattern / cross over point ?


boosts to 10 then 8 psi then 10 ?

:confused:


Shaq
12.7 on stock twins @ 1 bar (i reckon i can do better!)

boltoa

Hi Shaq

Check out the thread here. I had what sounds like the same problem, fixed by swapping two solenoid connectors over (took about 15 mins mainly taking off strut brace (6 bolts) and pressure tank (2 bolts). Apparently they get swapped because an old workshop manual showed them incorrectly. Check out the link in the first post in that thread for a great page on boost problems.

Hope that helps.

Andrew

BlitzBoy

Yo Shaq its Mark, I will ring ya tonight, I will check your solenoids if you want, I checked mine last night dead easy. I found a slight boost leak on mine where the y pipe is
"Piston Killa" 3rd Gen\'94 \'Oldone Racing Full Bridge Ported REW 13b engine with SCR seals\'. HKS T51 KAI turbo BBM mapped Motec ECU

JDS/HKS Street Class Championship Runner up 2011
Rotorstock winner 08,09
http://pistonkilla.blogspot.com/
old spec HB T51 470 @ wheels @ 1.2 BAR, 555 @ fly 10.46 @ 130 @ 1.25 Bar
new spec FB T51 482 @ wheels @ 1.15 BAR, 570 @ fly

New Project
"el fénix" RX2 by Mark & Mark

Shaq

boltoa
 
 cool thanks i will have a look tonight


 Blitz boy,

hey mark give us a buzz tonight i will be polishing my car you can come over around 5:00 if you have the time cos i know you r busy tonight :p


Shaq
12.7 on stock twins @ 1 bar (i reckon i can do better!)

Archbish

((hint: if you\'ve a hose that comes off loads, a bit of silicone sealant around the nipple will hold it in place...Nipple on the car, that is...))
Everyone wants to be like ArchBish,
Cos the Bish is never glum.
Its hard to be unhappy
when the sun shines out your bum