Hi i have some FBs lying around and other spares is there anything anyone needs before i scrap them to list a few
2x Rear Axels
2x fb Gearbox
Suspension
window motors
blown 12a engine
and more
just reply to the post for info they have to be scrapped at the end of may can take a hole car if needed but they have been used for donor parts so alot missing
what models / years are they as the gearboxes and rear ends changed:yes
And perhaps I could have the Reg\'s and colours as well as models/years, in order to check them off my list of runners (if they\'re on there - list goes back before 2000 on some cars).
Mate,
I could use spare axles of both types as donors for shot blasting/power coating, and the FB gearboxes too as some series insist..
Can always make use of bumpers/wings/doors etc too.
Redhill isn\'t far for me so could come and collect - how much are you after?
S.
Ok I will start stripping them this weekend I am not after silly money more that they need to go as I am moving out of my workshop and don’t want to waste good parts how far away are you from redhill?
car years are 84 and 83 i think
Hi,
Are they both basket cases or are the shells sound? I do have storage available for one of them if needed and am looking for a good shell for my Australian IPRA project. On closer inspection the one I bought recently has too much rust around the rear inner wheel arch so I\'m trying to find a better one for dipping if I can.
OK, let me know - I\'m only in West End - Woking.
Cheers
S.
i need a decent thermostate neck if you have one?
Mark
Stacy how much are you looking at spending on a good shell? as I am trying to sell my project car but there\'s not really much interest so am considering stripping it to sell in parts the ad is in the for sale section the yellow one as for the other shells there’s quite a bit of rust. If you like you are welcome to have a look at them and see what you want am off to Australia myself at the end of next month hence everything must go :)
I should have a filler neck will have a look
Quote from: ggs1981;610148Stacy how much are you looking at spending on a good shell? as I am trying to sell my project car but there\'s not really much interest so am considering stripping it to sell in parts the ad is in the for sale section the yellow one as for the other shells there’s quite a bit of rust. If you like you are welcome to have a look at them and see what you want am off to Australia myself at the end of next month hence everything must go :)
I should have a filler neck will have a look
cheers are we talking about the same part, its where the thermostat sits it\'s not a filling point on a 1st gen can bung a photo up
also how easy was it to fit the FD brake booster?
thanks
Mark
hmm! You are right I should come and have a look. Must admit I saw the yellow car, but thought a) you\'d want too much money b) I was alarmed at the idea of getting another "project"!
You never know it might follow you out to Oz after all..
I can\'t seem to PM you (mine works but it says you\'re doesn\'t?) how can we get in touch without posting info for permanent consumption...?
S.
Stacy my Email rx7ggs@hotmail.com (rx7ggs@hotmail.com)
MPK490p sorry I know the part your after will look tomorrow to see what condition it’s in
The FD servo went straight in I used the FB and FD spacers its about 1" thick only thing is you need to use the FD clutch servo or block off the pipe connection from the brake master as on a FD they share the reservoir
Quote from: ggs1981;610214MPK490p sorry I know the part your after will look tomorrow to see what condition it’s in
The FD servo went straight in I used the FB and FD spacers its about 1" thick only thing is you need to use the FD clutch servo or block off the pipe connection from the brake master as on a FD they share the reservoir
Nice thanks :yes
Mark
Email Sent, I need some parts. :wave
Quote from: mpk490p;610219Nice thanks :yes
Mark
any joy with that thermostat housing?
thanks
Mark