Mazda Rotary Club

General => General Technical => Anything Engine/Performance/Tuning related => Topic started by: barry798 on September 17, 2006, 06:07:42 PM

Title: rebuild/fitting single turbo
Post by: barry798 on September 17, 2006, 06:07:42 PM
hi all, had my 1 rx7tt on the road 2 weeks then off road for 5 month awaiting parts ,just rebuilt it and fitted it in this weekend put on new single turbo which i got cheep but need help on the air pipes as whot to keep and whot to blank off as well as the actuator piping any one have pictures etc
many thanks barry
Title: rebuild/fitting single turbo
Post by: antnicuk on September 17, 2006, 06:57:38 PM
there have been many threads about this sort of thing,  i think i have written up a few myself.

try searching through some old threads, the info is definately there.
Title: rebuild/fitting single turbo
Post by: barry798 on September 17, 2006, 07:30:51 PM
thanks had a look but could not see any ill have another go
Title: rebuild/fitting single turbo
Post by: antnicuk on September 17, 2006, 08:01:57 PM
maybe one of the mods could assist, i\'m no expert on searching
Title: rebuild/fitting single turbo
Post by: antnicuk on September 17, 2006, 08:17:49 PM
i found this write up that i did for a guy, not how helpful it is

I got rid of ALL the solanoids under the plenum, I have a vacume line to the fuel press reg, one to the external wastegate, one to the electronic boost controller one to the map sensor and one to each oil injector. I cut all the plugs and wires out of the loom and sealed the wires to ensure no shorts. Obviously the two duty solanoids are gone and all the associated vacume pipes. One of the best bits (apart from the extra power) of going single is the much simpler engine bay and no unfindable falts in amongst the nest of pipes. The wiring loom is also much smaller and lighter and again easier should you get a fault. You only need plugs for the TPS, Map sensor, four injectors, air temp, knock sensor and fuel temp if you use it. I cant think of anything else but i may have forgotten something which i\'m SURE someone will be only too glad to point out!
Title: rebuild/fitting single turbo
Post by: barry798 on September 18, 2006, 05:24:55 PM
thanks think ill have to get some one round
Title: antnicuk
Post by: barry798 on September 20, 2006, 06:00:47 PM
hi ya are you up to anthing the weekend
Title: rebuild/fitting single turbo
Post by: antnicuk on September 20, 2006, 08:30:06 PM
i\'m going to the lake district this w/end,  i could pop up monday morning on my way to work if you like, i start at 2pm on monday,   it wont take long.
Title: rebuild/fitting single turbo
Post by: barry798 on September 20, 2006, 09:02:45 PM
hi ya the cars going to haywood and scot to have a center section made as the down pipe fron the turbo is diferent hopfully get it back friday arfter noon it going on a lowlowder
Title: rebuild/fitting single turbo
Post by: antnicuk on September 20, 2006, 09:18:04 PM
do you mean this friday coming?
Title: rebuild/fitting single turbo
Post by: barry798 on September 20, 2006, 09:36:55 PM
na going away monday morning 25th and getting it back friday 29th thats the only time i can get it there
Title: rebuild/fitting single turbo
Post by: barry798 on September 27, 2006, 08:40:27 PM
hi ya barry here you up to anything the week end
Title: rebuild/fitting single turbo
Post by: antnicuk on October 01, 2006, 12:05:51 PM
give me a call to arrange
regards
tony
07968 061 567