Text only | Text with Images

Mazda Rotary Club

General => General Technical => Anything Engine/Performance/Tuning related => Topic started by: B9 KLF on October 16, 2005, 08:56:52 PM

Title: Knightsport V Mount
Post by: B9 KLF on October 16, 2005, 08:56:52 PM
Pics of the excellant work done by RE:Worx to install my v mount. At the same time viton turbo pipe replacement, enfini y pipe, greddy elbow, metal AST, and the CAI air groove induction kit. In the second pic you can see the CAI inlet above the air con rad.

No vented bonnet and temps for the rad 83-85 and 1/c during the summer of around 30 - but it depends on ambient temp really and what your doing at the time.

Some folks complain about the cost of Knightsports products but the RE:Worx crew charged a days labour fitting the kit and the induction and said that all the bits where in box  - so overall it\'s not costly and also very tidy.

I\'m pleased  :cool

Keith
Title: Knightsport V Mount
Post by: B9 KLF on October 16, 2005, 08:58:47 PM
The CAI air groove induction kit to the top left of my air con rad - nice subdued noise
Title: Knightsport V Mount
Post by: B9 KLF on October 16, 2005, 09:00:05 PM
Sexy eh   :cheers
Title: Knightsport V Mount
Post by: tr1cky on October 16, 2005, 10:02:11 PM
Very tidy install there mate, looks like the boys have done a top job again! ;)

Quick Q- do you have to use the Knight sports induction system with there V mount??

Cheers Rich
Title: Knightsport V Mount
Post by: B9 KLF on October 16, 2005, 10:44:31 PM
QuoteQuick Q- do you have to use the Knight sports induction system with there V mount??


No - but I could\'nt resist it. When the single comes along I hope I can sell it on.

Keith
Title: Knightsport V Mount
Post by: tr1cky on October 17, 2005, 09:04:32 PM
Nice one ;)

Cheers Bud
Title: Knightsport V Mount
Post by: JP825 on October 18, 2005, 10:46:59 AM
Can I just ask where you get the pipe between the Greddy elbow and the intercooler pipe?? ( The little one between it)
Title: Knightsport V Mount
Post by: Sy. on October 18, 2005, 12:07:51 PM
looks well good . Very nice and tidy .
Can you give me a ball part figure for the whole install .
Title: Knightsport V Mount
Post by: B9 KLF on October 18, 2005, 12:41:24 PM
QuoteCan I just ask where you get the pipe between the Greddy elbow and the intercooler pipe?? ( The little one between it)

The make up pipe was supplied by RE:Worx at the time but a straight length should not be too difficult to source.

QuoteCan you give me a ball part figure for the whole install .

If you look at their site the parts are on there and then add a days labour and VAT. Your\'ll need to have a remap though and I trust you have got a programmable ecu?  :yes

Keith
Title: Knightsport V Mount
Post by: memski on October 18, 2005, 05:02:33 PM
Very nice Keith  :cheers  I thought an engine rebuild was on the cards or have I missed something?

And is that a redtop battery I spot? :god  Very nice had one in my old car which is going into the fd\'s boot when I get round to it :D
Title: Knightsport V Mount
Post by: B9 KLF on October 18, 2005, 11:19:38 PM
Yes to both memski - Ive blown a seal. The water problems where in fact the housing seal and in the end it would\'nt start hot and coughed up a lot from cold. So instead it\'s in for the rebuild and street port - been an expensive year  :flamed

It is a red top and fits in nice since I did not want a batt in the rear seats.


Keith
Text only | Text with Images