Mazda Rotary Club

General => General Technical => Topic started by: Mulv on July 31, 2005, 05:04:47 PM

Title: How long can it stand for???
Post by: Mulv on July 31, 2005, 05:04:47 PM
just a quick one, my turbo is off the car being repaired, and she has been standing for 2 months now.

hoe long can I leave it as i dont want her to seize up at all, I assume i cant turn her over with the turbo and related bits off the car??

thanks Graham
Title: How long can it stand for???
Post by: sdminus on July 31, 2005, 05:10:46 PM
When I left mine over the winter I gave the main pulley a couple of turns a week to keep the seals the stuff nice and free. I used a 19 mm socket. Be sure to turn it the correct way... Sunday afternoon job on the way back from the pub!!!

Scott
Title: How long can it stand for???
Post by: TRex on July 31, 2005, 05:12:21 PM
Advise removed, as always there is someone here with a lack of knowledge that feels they know best.

 rgds
Title: How long can it stand for???
Post by: Mulv on July 31, 2005, 05:45:24 PM
thanks, so if i take the plugs out and turn it over, even with the manifold exhaust and wastegate off it will be ok???
Title: How long can it stand for???
Post by: sdminus on July 31, 2005, 05:53:08 PM
I didnt remove the plugs. Just turn it over
Scott
Title: How long can it stand for???
Post by: grinder on July 31, 2005, 09:05:19 PM
any news on the turbo matey ??
Title: How long can it stand for???
Post by: TRex on August 01, 2005, 04:58:43 AM
Good luck,
Title: How long can it stand for???
Post by: nikp on August 01, 2005, 10:34:23 AM
I had mine standing for about 3 months - did nothing to it, and it was fine. Didn\'t even turn the engine.

However, you don\'t really need to take the spark plugs out to allow turning the enigne easier, as at that slow speed the apex seals will not seal properly, and no compression of air will be being made - therefore the engine should be easy to turn over - you can grab one of the drive belts and turn it over, it\'s that easy!
Title: How long can it stand for???
Post by: Mulv on August 01, 2005, 11:15:56 AM
still waitig grinder, they are having probs getting parts
Title: How long can it stand for???
Post by: MillSpeed on August 01, 2005, 11:26:22 AM
Quote from: nikpat that slow speed the apex seals will not seal properly, and no compression of air will be being made - therefore the engine should be easy to turn

Ah so that\'s why. I was always a bit concerned by how easily my engine would turn over by hand, but of course there\'s only the strength of the apex seal springs letting you build up any compression. I still need to compression test my engine tho.
Title: How long can it stand for???
Post by: ds2000 on August 01, 2005, 01:56:06 PM
Which way is the correct way? CW or ACW?
Title: How long can it stand for???
Post by: nikp on August 01, 2005, 01:59:23 PM
I am no expert at this point, but with these engines, i don\'t think it matters.
Title: How long can it stand for???
Post by: MillSpeed on August 01, 2005, 02:02:46 PM
Well the engine rotation is CW when looking from the front, so it\'d prob be best to rotate it CW, but like nikp says it probably doesn\'t matter.
Title: How long can it stand for???
Post by: Zimmy on August 05, 2005, 02:01:47 PM
I got mine started - after it had been sitting off road outside for 3-4 Years!
Ok it had been started 2 years ago too. What I was told was remove the EGI fuse to prevent flooding and turn it over a bit to get the oil up and about.

The only thing I had to do was charge the battery put new petrol in it as the stuff in it had went off. The tyres hadn\'t fared well either so its worth turning them every month or two and make sure they don\'t get flat.

 So 2 months should not be a problem!

Changed the oil and its running like a sweetie now. :)

Z