Print Page - induction kit

Title: induction kit
Post by: colinrx7surrey on April 07, 2005, 12:24:25 PM

wat is the best induction kit to fit a 2nd gen fc3c?
cheers
colin

Title: induction kit
Post by: grinder on April 07, 2005, 12:30:09 PM

errr no idea to be honest

the flat panel K&N is OK i would assume - depens on what you are running and/or hoping to do to the car

Title: induction
Post by: colinrx7surrey on April 07, 2005, 12:37:44 PM

im currently runing a hks flat panel instead of the standard panel,,,just lookin to upgrade the bhp a little,and also looking to get rid of the standard flat panel box.perhaps maybe a k@n cone filter!

Title: induction kit
Post by: Brett on April 07, 2005, 12:38:39 PM

Providing you either remove the FTP lense on the aFM side, or fit a vented headlamp cover, or like me dont care about heatsoak in traffic, then the K&N induction kit is good, but expensive. I ran with a K&n panel for awhile too. It all depends on what you want to do with the car. K&N panel makes a difference, K&N filter makes a bigger difference, but also shows up a flat spot when the secondary injectors come on. (Well on my EGi anyway)

Title: induction kit
Post by: grinder on April 07, 2005, 01:24:20 PM

dibs in the panel filter if you upgrade :)

Title: induction kit
Post by: colinrx7surrey on April 07, 2005, 01:34:02 PM

sure...if i do upgrade...where bouts u based?

Title: induction kit
Post by: grinder on April 07, 2005, 02:38:51 PM

im up in chorley/lancs - so no where near you

although should be at rotorstock :)

Title: induction kit
Post by: Brett on April 07, 2005, 03:15:11 PM

Stu, assuming your FC is on the road by RS your going to have to fit a tow bar for the amount of stuff you intend to bring with you and bring back! :rollin

Title: induction kit
Post by: Big Stu on April 07, 2005, 03:21:11 PM

QuoteOriginally posted by Brett
Stu, assuming your FC is on the road by RS your going to have to fit a tow bar for the amount of stuff you intend to bring with you and bring back! :rollin

Can you get a roofrack for an FC????

:rollin :rollin :rollin :rollin :rollin

Title: induction kit
Post by: Brett on April 07, 2005, 03:34:17 PM

I\'m not sure, but Stu\'s pretty handy with a mig welder now, so I expect he can make one!

Title: induction kit
Post by: Big Stu on April 07, 2005, 03:42:28 PM

QuoteOriginally posted by Brett
I\'m not sure, but Stu\'s pretty handy with a mig welder now, so I expect he can make one!

Now that id like to see.

Maybe Grinder would like to go down the same route as the sultan of Brunie ( crap spelling), and convert his FC into an estate LOL

Title: induction kit
Post by: Brett on April 07, 2005, 03:55:36 PM

If no one buys my EGi, I might do it myself! :D

Title: induction kit
Post by: Thud on April 07, 2005, 04:00:27 PM

QuoteOriginally posted by Big Stu
Can you get a roofrack for an FC????

Actually much to my amazement you can! You can get a kit for a 2nd Gen. Front bar fits like on a normal car but you need an extender which places the back bar over the rear window.

Bound to lose you major street cred though...

Title: induction kit
Post by: grinder on April 07, 2005, 04:05:45 PM

heeeeeyyyyyyy calm down !!

LOL

i didnt think i was talking anything with me and bringing anything back - unless you all want to donate parts to the

"help save the FC fund" ????

Title: induction kit
Post by: Brett on April 07, 2005, 04:06:36 PM

Might offset a few of the chav points though :rollin :rollin

Title: induction kit
Post by: Brett on April 07, 2005, 04:08:03 PM

Ok, I\'ll donate a complete set egi wheels. :bandit

Title: induction kit
Post by: Big Stu on April 07, 2005, 04:09:20 PM

QuoteOriginally posted by grinder
heeeeeyyyyyyy calm down !!

LOL

i didnt think i was talking anything with me and bringing anything back - unless you all want to donate parts to the

"help save the FC fund" ????

I thought we had agreed in a previous post that:

GRINDER, HE HAVE NO RX7??

Or are you trying to built one from scratch?

Title: induction kit
Post by: Brett on April 07, 2005, 04:13:47 PM

Well theres two schools of thought:-

1) He\'s built it from the ground up by now with the amount of welding thats gone on.

2) Scoobi Si gave him Rx Rentals business card.....

Title: induction kit
Post by: Big Stu on April 07, 2005, 04:21:25 PM

QuoteOriginally posted by Brett
Well theres two schools of thought:-

1) He\'s built it from the ground up by now with the amount of welding thats gone on.

2) Scoobi Si gave him Rx Rentals business card.....

Now thats comedy!!!

:rollin :rollin :rollin :rollin :rollin :rollin :rollin

( for god sake man stop clicking the smily)

Title: induction kit
Post by: grinder on April 07, 2005, 04:38:03 PM

QuoteOriginally posted by Big Stu

GRINDER, HE HAVE NO RX7??

thats bloody gurj starting that - just wait till i see him at RS !!

Title: induction kit
Post by: Brett on April 07, 2005, 04:38:32 PM

QuoteOriginally posted by Big Stu
Now thats comedy!!!

:

Well its better than working! :D

Title: induction kit
Post by: Brett on April 07, 2005, 04:39:30 PM

Just claim you have an at-at, like in your avatar!

Title: induction kit
Post by: grinder on April 07, 2005, 04:51:02 PM

i have ........

.... but it needs some welding :rollin

Title: induction kit
Post by: Brett on April 07, 2005, 04:52:29 PM

....curse those rebels.....

Title: induction kit
Post by: hawker182 on April 09, 2005, 12:54:15 AM

lol funny funny funny

Title: induction kit
Post by: scooby_si on April 10, 2005, 11:40:21 AM

QuoteScoobi Si gave him Rx Rentals business card

please no advertising on the board else i\'ll have to slowly put your gonads thru a liquidiser

& the correct name is REX RENTALS (http://instagiber.net/smiliesdotcom/contrib/icw/010.gif) lol
Si

Title: induction kit
Post by: Brett on April 10, 2005, 12:49:41 PM

QuoteOriginally posted by scooby_si
please no advertising on the board else i\'ll have to slowly put your gonads thru a liquidiser

Promise? :D

Title: induction kit
Post by: grinder on April 11, 2005, 09:02:51 AM

and so it begins !!

Title: induction kit
Post by: Brett on April 11, 2005, 09:37:07 AM

I was thinking, maybe we can start up an FC club, call it TEAM OXIDE maybe we could get bulk discount on welding supplies and underseal?

Any takers? :rollin :rollin :rollin

Mazda Rotary Club

Cars by Model Type => 2nd generation RX-7's => Topic started by: colinrx7surrey on April 07, 2005, 12:24:25 PM