Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Mazdarotaryparts

Pages: [1] 2 ... 43
1
Rotary and General Chit-Chat / Re: TODAYS QUICK PIC
« on: September 15, 2018, 10:22:51 AM »
 :great:

2
RX-8's / Re: Oversized side seals, good or bad?
« on: March 20, 2018, 06:49:03 PM »
We supply many company's deliberately non Europe with longer side seals so the builder can grind the ends to get the best fit for each groove.

With the grooves cleaned and lightly oiled you should just feel the side seal move to and fro under your fingers without measuring, this is how the Mazda engine builders put them together in Japan by feel  ;)

Only available out from Japan or America via Japan, most term these longer seals as "Mazdaspeed side seals"

For the ends, just replicate the side seal ends you take out.

Here is a link that may help your re-build

https://www.racingbeateurope.com/b-rx8-rotary-internal-engine-partsb-459-c.asp

Hope this helps

     

3
Rotary and General Chit-Chat / Re: Clive's 400 BHP Super GT RX-8 Race Car
« on: November 02, 2017, 08:57:28 PM »
Spoke with Jon this morning and checked a couple of things out,

Not actually driven the car but no codes showing in the ECU, also checked the battery as I had a different battery.

Still showing 12.6 volts. Balanced charged correctly with a 13.88 end voltage so it looks like no spike from this.

Still looks like it was something screwed in the ABS system from when I had the rear sensors disconnected  ???   

4
General Technical / Re: how do i make a rotary rev to the moon?
« on: November 10, 2015, 08:09:26 AM »
Here we go, if you follow this link to the Racing Beat page it will give you info and how to keep the stationary gear in place in the Rotor above 8500

http://www.racingbeat.com/mazda/performance/rotary-tech-tips/rotors.html

5
Rotary and General Chit-Chat / Re: Gurning! go one do it i dare you!
« on: November 06, 2015, 05:29:33 PM »
Excellent, made me smile :whoo:

6
Wanted Items / Re: RX8 standard exhaust.
« on: November 05, 2015, 08:29:27 AM »

Jon we have a special £100 off offer on a Racing Beat single tip on offer that’s seen below which is quiet enough to be track day friendly and fine on low revs as long as its not fitted with a plain de-cat pipe ---------------plus its super light and will make you go faster  ;)

Her you go, her's a link below

http://mazdarotaryclub.com/forum/index.php?topic=83469.0

7
Wanted Items / Re: FB headers
« on: August 18, 2015, 09:05:39 AM »
Not sure if you have already found this but we can supply Racing Beat FB or complete FB systems which can be found on this link below

http://www.racingbeateurope.com/bfb-exhaust-system--intake-b-322-c.asp

Hope this helps


8
Wanted Items / Re: Rear ARB Linkage
« on: August 18, 2015, 08:57:35 AM »
If you would like to either send us an e-mail or give us a ring on 01474 777800 we can organise your new ball joint if you wish.

9
Parts for sale / Re: Looking for FD facelift bumper
« on: August 01, 2015, 12:27:12 PM »


I'm looking for a '99 spec frontbumper or a replica (plateless replica prefered over all), i've been scearching for more than 3 months now, but with out any succes.

Hi Sebastiaan,

Reference looking for your bumper, we can supply a new original 99 spec genuine Mazda nosecone for £492 with £40 for delivery  including vat

Hope this helps


10
RX-8's / Re: Few questions about RX-8
« on: August 01, 2015, 12:21:29 PM »
It may help to know that its no problem sending a complete clutch across to to Finland as we send these all over the world,

Details can be found on the link below,

http://www.mazdarotaryparts.com/b-rx-8-clutch--transmissionb-306-c.asp


11
3rd generation RX-7's / Re: Which exhaust for track use?
« on: July 17, 2015, 06:43:23 PM »
Many many people over the years have used the Racing Beat 3" cat back that we supply with no noise problems,

Available as a Single tip and also as a twin tip, which  sells particularly to the stock cars  as the closest looking to stock you can buy.

http://www.racingbeateurope.com/bfd-ex001-racing-beat-single-tip-cat-back-exhaustb-1178-p.asp

http://www.racingbeateurope.com/bracing-beat-dual-tip--cat-back-exhaust-for-rx-7-fdb-1168-p.asp




12
Cosmo's and Other Rotary Powered Vehicles / Re: Westory Progress.
« on: March 17, 2015, 09:49:48 AM »
Rainy nasty day here, pictures will cheer us up  ;)

13
Wanted Items / Re: Wanted: FD clutch kit standard or aftermarket
« on: January 08, 2015, 09:49:01 PM »
Hi Robbie,

If you would like to follow the link below we have from stock to race clutches available,

http://www.mazdarotaryparts.com/bfd-clutch--transmissionb-273-c.asp

We hope this helps


14
Wheels & Tyres, Suspension & Brakes / Polybush Wishbones etc.
« on: November 13, 2014, 10:30:48 AM »
It may help to know that we sell Power Flex Bushes via the link below which if using the car on track will be a little firmer and better than Polybush

http://www.racingbeateurope.com/bfd-suspensionb-282-c.asp

We hope this helps

15
Hi Marcus,

Coils are very easy to change and we send out a simple step by step guide to help.

Beware of fake coils as many on the market are sold as genuine and are not leading to many customers then arriving at our doorstep after finding the car still won\'t run properly !

Here\'s a link should you wish to buy.

http://www.mazdarotaryparts.com/b-mazda-rx8-100-genuine-ignition-coils-set-of-four-b-1399-p.asp

Pages: [1] 2 ... 43