Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Mazdarotaryparts

Pages: [1] 2 ... 38
1
Rotary and General Chit-Chat / Re: TODAYS QUICK PIC
« on: September 15, 2018, 10:22:51 AM »
 :great:

2
RX-8's / Re: Oversized side seals, good or bad?
« on: March 20, 2018, 06:49:03 PM »
We supply many company's deliberately non Europe with longer side seals so the builder can grind the ends to get the best fit for each groove.

With the grooves cleaned and lightly oiled you should just feel the side seal move to and fro under your fingers without measuring, this is how the Mazda engine builders put them together in Japan by feel  ;)

Only available out from Japan or America via Japan, most term these longer seals as "Mazdaspeed side seals"

For the ends, just replicate the side seal ends you take out.

Here is a link that may help your re-build

https://www.racingbeateurope.com/b-rx8-rotary-internal-engine-partsb-459-c.asp

Hope this helps

     

3
Rotary and General Chit-Chat / Re: Clive's 400 BHP Super GT RX-8 Race Car
« on: November 02, 2017, 08:57:28 PM »
Spoke with Jon this morning and checked a couple of things out,

Not actually driven the car but no codes showing in the ECU, also checked the battery as I had a different battery.

Still showing 12.6 volts. Balanced charged correctly with a 13.88 end voltage so it looks like no spike from this.

Still looks like it was something screwed in the ABS system from when I had the rear sensors disconnected  ???   

4
General Technical / Re: how do i make a rotary rev to the moon?
« on: November 10, 2015, 08:09:26 AM »
Here we go, if you follow this link to the Racing Beat page it will give you info and how to keep the stationary gear in place in the Rotor above 8500

http://www.racingbeat.com/mazda/performance/rotary-tech-tips/rotors.html

5
Rotary and General Chit-Chat / Re: Gurning! go one do it i dare you!
« on: November 06, 2015, 05:29:33 PM »
Excellent, made me smile :whoo:

6
RX-8's / Re: Few questions about RX-8
« on: August 01, 2015, 12:21:29 PM »
It may help to know that its no problem sending a complete clutch across to to Finland as we send these all over the world,

Details can be found on the link below,

http://www.mazdarotaryparts.com/b-rx-8-clutch--transmissionb-306-c.asp


7
3rd generation RX-7's / Re: Which exhaust for track use?
« on: July 17, 2015, 06:43:23 PM »
Many many people over the years have used the Racing Beat 3" cat back that we supply with no noise problems,

Available as a Single tip and also as a twin tip, which  sells particularly to the stock cars  as the closest looking to stock you can buy.

http://www.racingbeateurope.com/bfd-ex001-racing-beat-single-tip-cat-back-exhaustb-1178-p.asp

http://www.racingbeateurope.com/bracing-beat-dual-tip--cat-back-exhaust-for-rx-7-fdb-1168-p.asp




8
Cosmo's and Other Rotary Powered Vehicles / Re: Westory Progress.
« on: March 17, 2015, 09:49:48 AM »
Rainy nasty day here, pictures will cheer us up  ;)

9
Wheels & Tyres, Suspension & Brakes / Polybush Wishbones etc.
« on: November 13, 2014, 10:30:48 AM »
It may help to know that we sell Power Flex Bushes via the link below which if using the car on track will be a little firmer and better than Polybush

http://www.racingbeateurope.com/bfd-suspensionb-282-c.asp

We hope this helps

10
Hi Marcus,

Coils are very easy to change and we send out a simple step by step guide to help.

Beware of fake coils as many on the market are sold as genuine and are not leading to many customers then arriving at our doorstep after finding the car still won\'t run properly !

Here\'s a link should you wish to buy.

http://www.mazdarotaryparts.com/b-mazda-rx8-100-genuine-ignition-coils-set-of-four-b-1399-p.asp

11
Quote from: Kevp;883668
Hi Clive
I take it this will be ok for a HKS downpipe ?

Kev.


Yes:Thumbs-up

12
Hi Ash,

We have Racingbeat gaskets in stock the size you need ,

£8.50 plus £2.00 post

If you would like to send over the £10.50 over via PayPal to sales@racingbeateurope.com we will put one in the post.

13
General Technical / Surf City Garage - Beyond Clay Paint Polish
« on: April 25, 2014, 06:40:54 PM »
Hi Daniel

Why not take a look at the Surf City Garage Beyond Clay paint polish that we sell via
http://www.shyauto.com/bbeyond-clay-paint-polishb-1581-p.asp

Before you get that new paint job costing thousands of pounds, restore your faded paint with Beyond Clay.

This revolutionary polish does everything a clay bar does and beyond! Plus it\'s 100% safe for all surfaces, even clear coats.

Don’t waste money on clay bars. You don’t need them when you use Beyond Clay. Beyond Clay is a paint polish that does not contain harsh physical abrasives like many polishes out there.

Worth taking a look at the video link and the review.

14
1st generation RX-7's / clutch master cylinder
« on: February 09, 2014, 06:21:42 PM »
We can supply a rebuild kit at £24

Could you tell us if the flange that meets the bulkhead is at a 45 degree angle or 180 degrees to the reservoir as we have supplied these before and they have come up wrong

15
Racing Beat have just told me that if you use an early 13B sump with the 12A  front cover it will let the TII bolt straight in by using the RB mounting brace.

Pages: [1] 2 ... 38