Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - antnicuk

Pages: [1] 2 ... 13
1
Parts for sale / FS: Unbranded complete decat exhaust £50
« on: June 09, 2013, 03:33:24 PM »
Stainless 3 inch decat with rear box.






2
Complete as per picture from an FD with 58k miles.


3
Parts for sale / TII Gearbox for sale. £60 collected
« on: June 05, 2013, 10:11:42 PM »
I have the gearbox for sale which was a spare for my kit car.  It came from a car with circa 80k on it.  No clutch fork with it.

£60 collected from Near Harlow in Essex.

4
Parts for sale / Set of 4 White BBS wheels 16x 7.5 £60
« on: June 01, 2013, 11:02:52 AM »
Selling these on behalf of Jit but they are at my house near harlow for collection.

They have no damage but have been sprayed white.  










5
Parts for sale / RX8 Bonnet in black for sale
« on: June 01, 2013, 09:29:54 AM »
I have a black RX8 bonnet for sale.  It is in good condition but has a few small dints in it from a hail storm.  There is no damage but in certain lights you can see 5 or 6 dints.  Hence £30 collected from Near Harlow in Essex

6
Parts for sale / 2 RX8 wheels for sale
« on: June 01, 2013, 09:27:59 AM »
I have a pair of early 5 spoke RX8 wheels in silver.  They are straight and have no damage but the laquer has started to bubble.  They both have legal (just) bridgstones on them and would be good as a spare or for some drift or track day wheels.

£30 each collected or £55 for the pair.

7
Parts for sale / A few TII bits forsale
« on: May 27, 2013, 10:28:10 PM »
I am having a clear out of my workshop and everything rotary related is being sold.  There are a lot of FD bits but i have put these on an FD specific forum first along with some of the aftermarket bits,  the below bits are from my Kit car which was running a Turbo II engine.

I would prefer for items to be collected from Near Harlow in essex. No Dibs im afraid, whoever pays gets it.  Not sure if i can get PM\'s but my email is antnicuk@msn.com, same for paypal.

Turbo II turbo complete with manifold, good working order, was removed from my kit car when i went for a TO4E


Turbo II engine block in bits,  the plates are all good and mildly street ported,  the rotor housings are not usable.  The tension bolts, E shaft, corresponding pulley are there along with LIM and UIM and water pump housing. This engine made 330bhp at the wheels at reworx at 0.8 bar with a TO4E. There is also a spare end housing which hasnt been ported included (no rotors)  £100




Stock Turbo II clutch with plenty of life left in it.  £20




Twin belt alternator Pulley £10



Two TII alternators £15 each




Polished Series 4 Upper inlet manifold and throttle body £20




Polished Greddy elbow with 2nd boss for water injection (can be blocked easily and is underneath.  £30




Pair of Rotors machined to 3.5mm Apex seal grooves with complete set of matching apex seals and corner seals.  There are some dents to the faces of the rotors but they are perfectly usable. Bearings are good.  £100





 


TII Upper inlet manifold with throttle body and stock elbow and water pump housing.  £15

Pair of Stock TII engine mounts with no splits  £15

8
Items For Sale / FS: FD Gearbox and Uprated Exedy Clutch
« on: October 13, 2012, 09:54:49 PM »
Now that the project car has gone i have an FD gearbox that came out of the donor car. The car was standard with just under 60k miles so the gearbox is very good.
£175 collected, it also has a short shifter included.

I also have an uprated single plate clutch which has very little use and is in very good condition, i will get pics up later

£150, will send but at buyers cost

I also have a good complete fuel tank if anybody want one too.




9
Cars for Sale / First Gen FD Running Gear Project
« on: September 29, 2012, 11:10:20 PM »
I was really looking forward to getting this project done but it\'s not going to happen so its now on eBay!
 


http://www.ebay.co.uk/itm/1907320086...#ht_906wt_1140

http://www.ebay.co.uk/itm/1907320127...#ht_500wt_1157

11
RX-8 News and Information / RX8 ECU Reset procedure help
« on: September 01, 2011, 09:13:07 PM »
Hi
Can any one tell me the ecu reset procedure for the rx8,  i did get told it once by i have forgotten it  :confused:
thanks
tony

12
We have a track day at Cadwell next week (via MRC) so we have been preparing the kit cars over the last couple of weeks, including dynoeing, suspension set up and corner weighting this morning.  Both are finally ready so i took a couple of pics with my iphone.   Both are Rotary powered,  the Tiger (black) one is RX8 powered,  the stylus is rx7 turbo powered.

Roll on next week  :D










13
Rotary and General Chit-Chat / Any Architects on Here?
« on: July 15, 2010, 10:19:03 PM »
My local architect came to visit me yesterday to discuss my workshop build at the bottom of my garden, today he emailed me his prices which he agreed to do on a fixed price.

I was a little shocked to say the least as a i only want a square block workshop about 7m x 8m. with a shallow pith roof! Anyone got any ideas?

Work Stages

Initial payment £300.00+ VAT

Planning Application
A - Appraisal
B - Briefing
C - OutlineP roposals
D - Detailed Proposals
£975.00+ VAT
Payable on submission of Application

BuildingR egulationA pplication
E - Final Proposals
F- Productionln formation

£1.145.0+0 V AT
Payable on submission of Application

14
I want to make up a set of oil cooler lines as I want to fit a second cooler.  All the fittings i can find are screw in male or female with a push on tail, i cant find any banjos\'

Does anyone know what size fitting i would need to replace the stock mazda banjo with a screw in fitting?

15
I am clearing out my loft ready for an impending move.  I have a pair of good condition door cards in black with all lights and reflectors for a Turbo II coupe.  I cant bring myself to throw them so free to anyone who wants to collect.  I will not be packaging these i\'m afraid as they are awkward and big.

Pages: [1] 2 ... 13