Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Donato

Pages: [1] 2 ... 6
1
General Technical / Aaaahhh!!! Urgent Help Needed Please?
« on: July 28, 2006, 06:41:13 PM »
Seems the rotary gods are angry with me for trying to sell my car..between this problem and the broken headlight im going to pull my hair out!!

I had to take my dash apart to change the rev counter face, got it done, everything was working again, great, then had to disconnect and reconnect the fuel gauge. Got that working and then...

suddenly all the dash gauges stopped working, as well as the electric windows, and the radiator cooling fans have stopped working as well, the indicators aren\'t working but the hazard lights are...:2Mad

Everything else electrical seems to be working...

Please somebody help me!

2
I would like to lower the temperature that the cooling fans come on at by a few degrees, is it possible to do from the PFC controller or do you need to plug in a laptop??

Cheers

Donato

3
General Technical / Help on part number for 3rd gen please???
« on: March 02, 2006, 04:51:50 PM »
Hi, Im needing a mazda part number for the small cushioned interior panel that is next your left knee when you are in the driving position. Anyone?

Cheers

Donato

4
General Technical / Size of belt when air pump removed??
« on: October 24, 2005, 10:33:38 AM »
Anyone know the size of the belt that is required for the alternator/water pump when the air pump is removed? My one is at tyhe end of its life and need to get a replacment...

Your help would be greatly appreciated  :)

5
General Technical / Anyone help with this?? Max maybe??
« on: September 09, 2005, 11:01:53 AM »
Just wondering if anyone could help me out with the exact measurements? (please see the bottom of the page on attachment for details, sizes A B Z)

If not i will remove my wheel and caliper, but if someone has there car stripped then it would be very handy if you could help.

Thanks

Donato

6
3rd generation RX-7's / Pics of my new lights
« on: September 08, 2005, 11:27:47 AM »
What do you think guys? I like them...

7
3rd generation RX-7's / The Ultimate FD!
« on: July 08, 2005, 01:03:15 PM »
Just for fun, I would like you to tell us what your ultimate spec FD would look like and have inside it.

Basically if money was no object, just say you won the lottery, what would your mods be for creating the ultimate FD???  :chat

Cheers

Donato

8
I. C. E. & Electrical / Tweeters
« on: June 23, 2005, 04:50:15 PM »
Where would i fit such items for maximum performance...? :)

9
New to MRC - introduce yourself / New section for members.
« on: June 15, 2005, 01:02:00 PM »
Please post who you are in the sticky thread in the who\'s who section. Please read the second post in that thread on what to do and what not to do thanks.

Cheers

Donato :wave

10
Anything Engine/Performance/Tuning related / induction kit
« on: April 25, 2005, 04:54:41 PM »
Right, i need to replace my apexi induction as its too big for the space i have, i have had to crush one of the filters..

What am i best to go for?

Cheers

Donato

11
Anything Engine/Performance/Tuning related / New Rolling road figure.
« on: April 25, 2005, 10:24:37 AM »
Finally changed all soft pipes for hard pipes and replaced all hose clips. then turned the boost up from 0.74 to 0.9. Took it to a BMW rolling road day at Falkland performance and acheived 340bhp fwhp and 282 rwhp. Thats 25bhp more with the increase in boost and the lack of a collapsing pipe than i got at Noble with the MRC rr day.

The boost contoller (greddy profec b II) is kicking in and there is a drop in boost before it increases again half way through the run, which leads me to think i dont have it set up right, where am i going wrong?

Attached is the scan of my print out, any ideas guys? The car is running non sequential by the way..

Cheers

Donato

12
I. C. E. & Electrical / Help fitting ICE..
« on: April 12, 2005, 08:58:53 AM »
Right, when it comes to ice im clueless, and of my Scottish friends any good at it as i cant afford to get it done professionally, i can fit it all but i dont know what goes where, really need someone to point me in the right direction.

Can anyone help me?

Cheers

Donato

13
i dont really brand new car but it feels like it!

Fitted this kit at the weekend, i have to say its a fantastic improvement on the Ohlins coilovers! The coilovers were very good on track however, any journeys on the roads were full of bangs and bumps, cd\'s jumping, dentist bills physotherapy etc... and worst of all the handling across a bumpy road was actually worse.

The beauty of this is with the adjustment you can get in the flex kit you can enjoy your cd on the road. It has actually improved the handling on the road as it absorbs the bumps you would normally \'skip\' over and with a few clicks you can stiffen the car right up for the track.

And the car is lower now too.

Highly recommended! :D

Just like to say thanks  to Clive/Shy auto for my new car! ;)

14
3rd generation RX-7's / 3rd gen rear badge photo please?
« on: March 07, 2005, 04:45:28 PM »
Can someone please post up a pic reasonably close of the rear RX7 badge as i want to play with the design and get a custom one made?

Thanks

Donato

15
Anything Engine/Performance/Tuning related / Fitting gauges.
« on: March 03, 2005, 01:02:18 PM »
Im needing a little help in fitting my HKS gauges..

I have the oil and water temp ones sussed, however where exactly is the best place to tap the oil pressure guage into?

Cheers in advance

Donato

Pages: [1] 2 ... 6