Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - L18M

Pages: [1] 2 ... 240
1
Ah, was going to email u Aston but can't find your email from previous. Is it just o ring or do I need to use gasket too? Mines leaking :(
Thanks

2
Parts for sale / Re: RX7 FC3S turbo 2 parts
« on: January 30, 2016, 10:44:14 PM »
Hi, sorry to topic skip but how you plug in the fan relay? How is it activated to turn on? I've gone efan too but its hard wired in and always on.

3
Sent you email.
Thanks

4
as above really:

1) a pair of 1000cc injectors, top feed, high impedence

2) OMP "O"ring / gasket for 13BT (mine leaking)

3) ecu kick plate / cover for fc

4) fd oem fan set

Thanks

5
2nd generation RX-7's / Re: FC3S Rear Hatch Spoilers
« on: December 31, 2015, 07:37:40 PM »
epracing have one.
else keep checking ebay as they come and go from a seller in china.

i had a shine auto one but was very flimsy structurally as it only had 2 surfaces and broke easily.
i bought one from china which is a solid wing but hollow inside. much stronger and cheaper.

6
Parts for sale / Re: FREE FC3S T2 parts!
« on: May 31, 2015, 10:39:31 PM »
i just need driver side door handles, still available?
actually both doors available?

7
Parts for sale / Re: FS: 13BT FC engine TD06 greddy setup 1700£
« on: May 30, 2015, 11:14:52 AM »
And hks twin spark

8
Parts for sale / Re: FS: 13BT FC engine TD06 greddy setup 1700£
« on: May 30, 2015, 11:14:28 AM »
Front bumper for sale?

9
you'll easily see 400 with that set up.

not a very technical reply but most people i know running big power use bosch 044.

i had 374bhp (fly) with bosch 044, 550cc pri, 1680 secondary inj which was more than enough fueling and the secondaries didnt even break a sweat.
you'll have the same amount of fueling as me so you'll be fine

10
Anyone..?

Do these settings look right for running 550 primary, 1680 secondaries? More concerned why there no percentage figure for secondaries also latency figures. Any constructive input appreciated. Its ap engineering power FC for fc3s.


11
New to MRC - introduce yourself / Re: japfest
« on: May 24, 2015, 11:01:09 AM »
Ok thanks :)

12
New to MRC - introduce yourself / Re: japfest
« on: May 24, 2015, 01:18:58 AM »
When did that happen?

Boosted: know if they do mapping now? Or any rotary mappers in south west?

13
Parts for sale / Re: fc parts
« on: May 19, 2015, 11:27:16 AM »
Any chance of taking just the bottom clutch inspection plate with bolts please?

14
Rotary and General Chit-Chat / Re: The times they are a changing
« on: May 16, 2015, 01:18:27 AM »
I agree the forum does seem bit quieter these days. When I first joined, it was very busy.

Maybe there's enough Info on the site to solve most common problems with rotaries? Developing internet where solutions can be found on other websites?

Makes me wonder, if all the old boys retire from rotary rebuild/ tuning eg super 7, RX motors, ReWorx etc then who will replace them as specialists? I've not come across any new tuners.

15
After lots of searching i've found the following but need confirmation from a more knowledgeable person if you'd be so kind :)

OEM primary & secondary inj: 550cc / latency .73msec
Bosch 1680cc inj / latency .45msec (@14v)

so the setting adjustment i need on the hand commander for the 1680's are:

To work out injector size correction
Old SIZE / New Size = Correction
550/1680*100 = 32.7%

To work out latency:
New Latency - Old Latency = Latency Correction
.45-.73 = -.28

If that is correct, then i now need to know which injector numbers these need to go into?

Pages: [1] 2 ... 240