Recent posts

Pages: [1] 2 ... 5
1
RX-8's / Re: She's Back On the Road not completely done but good enough
« Last post by clive on December 14, 2018, 08:33:07 AM »
Have fun Sunday
2
RX-8's / Re: MX-5 NC with RX-8 231 Engine
« Last post by Paul_13 on December 13, 2018, 10:43:45 PM »
Still getting p0032. I've checked all wire connections and I'm getting a 0.32 ohm resistance reading on what should be the sensor earth back to the ecu... Something not right there. I'll just zero out the dtc I think.550 miles in now Sent from my SM-G965F using Tapatalk
3
Rotary and General Chit-Chat / Re: Rotus Project Build
« Last post by boosted on December 13, 2018, 09:44:17 PM »
Must be looking at old photo..tried hylomar nope. Original rubber seal dried up and cracked..made 1 out of ptfe 1mm thick white sheet i procured from work.  Made a gasket a ring with the stud holes stamped out. Sent from my SM-N950F using Tapatalk
4
Rotary and General Chit-Chat / Re: Rotus Project Build
« Last post by Jamie R on December 13, 2018, 09:34:21 PM »
The black sealant was PTFE?
5
Rotary and General Chit-Chat / Re: Rotus Project Build
« Last post by boosted on December 13, 2018, 09:19:29 PM »
I used a few materials and the ptfe 1 i made has been onit 3 years no leak. Ill link tilton pedals..demon tweeks. Sent from my SM-N950F using Tapatalk
6
Rotary and General Chit-Chat / Re: Rotus Project Build
« Last post by Jamie R on December 13, 2018, 09:06:47 PM »
Thanks for the heads up Jon. I can't seem to find tilton boxes, with cockpit mounted master cylinders, I need them pointed towards me because my roll cage will get in the way, That way I can put my heel board over them, and as the father in law wants to have a play on the track too  I'm making the pedal box adjustable coz he has didd [...]
7
RX-8's / She's Back On the Road not completely done but good enough
« Last post by exiled-viking on December 13, 2018, 08:05:00 PM »
yep got the rear end 90% done and she's back on the road hoping for a good day Sunday for a good blast ............
8
Rotary and General Chit-Chat / Re: TODAYS QUICK PIC
« Last post by exiled-viking on December 13, 2018, 07:56:38 PM »
9
Rotary and General Chit-Chat / Re: Rotus Project Build
« Last post by boosted on December 13, 2018, 04:11:46 PM »
Switches behind. Clutch switch alters idle in neutral. Id set a 1200 rpm idle brings the oil press up.Sent from my SM-N950F using Tapatalk
10
Rotary and General Chit-Chat / Re: Rotus Project Build
« Last post by boosted on December 13, 2018, 04:09:42 PM »
Tilton 600 series..floor or overhung mount. 2 pedal £280 from Merlin.I use the rx8 clutch and brake switch...2 ally tabs on top of pedals. Sent from my SM-N950F using Tapatalk
11
Rotary and General Chit-Chat / Re: Clive's 400 BHP Super GT RX-8 Race Car
« Last post by boosted on December 13, 2018, 03:00:34 PM »
https://manualzz.com/doc/7305889/ibc-r-user-manual---from-tuner-toolsits all here.. p19 external wastegate plumbing with solenoid port numbers.
12
Rotary and General Chit-Chat / Re: Clive's 400 BHP Super GT RX-8 Race Car
« Last post by clive on December 13, 2018, 12:29:05 PM »
Thanks Jon, I never stop a good volunteer  I would be interested to see how they  plumb a single Turbo in the manual?. 
13
General Technical / Combined Front Strut Brace & Engine Damper
« Last post by SW7 on December 13, 2018, 11:05:15 AM »
Hi,Does anyone have any experience of using a Combined Front Strut Brace & Engine Damper, if so what do you think and which brand/make do you recommend?Cheers Steve
14
Rotary and General Chit-Chat / Re: Clive's 400 BHP Super GT RX-8 Race Car
« Last post by boosted on December 13, 2018, 07:28:08 AM »
https://id-workz.co.uk/gizzmo-ibc-r-boost-controllerthis is the link to the Gizzmo... Duty can be changed per 500 rpm so different boost settings at different rpms,launch  low rpm low boost wheel hook up boost.  4K high boost Rocket launcher modeI have this fitted on my car but not controlling boost, prob take me an hour to get out...happ [...]
15
Rotary and General Chit-Chat / Re: Rotus Project Build
« Last post by Jamie R on December 12, 2018, 09:57:13 PM »
How are your brake lights activated? In line pressure operated switch?
16
Rotary and General Chit-Chat / Re: Clive's 400 BHP Super GT RX-8 Race Car
« Last post by boosted on December 12, 2018, 09:50:46 PM »
Whohoo...Go Christine...Sent from my SM-N950F using Tapatalk
17
Rotary and General Chit-Chat / Re: Rotus Project Build
« Last post by Jamie R on December 12, 2018, 09:49:16 PM »
Nice one! I found obp to be cheaper tbh, oh and the fly by wire pedal boxes are ridiculously priced, I'll settle for the ergonomics of floor mounted brakes and top hung accelerator like you have considering it all works. I did consider converting the stock accelerator pedal in to a shortened lever operated by a Bowden cable with a traditional [...]
18
Rotary and General Chit-Chat / Clive's 470 BHP Super GT RX-8 Race Car
« Last post by clive on December 12, 2018, 09:36:13 PM »
This post is a thank you post to all you good people who have either assisted or supported my efforts through thick and thin, initially to get the car to win races and now to become a Championship Winning RX-8.  Because I was racing in a different series, on the day of the end of year Track Attack Trophy presentations, I obviously did not att [...]
19
Rotary and General Chit-Chat / Re: TODAYS QUICK PIC
« Last post by clive on December 12, 2018, 07:27:26 PM »
Mad Mike Whiddett's new 3 Rotor "in action"
20
3rd generation RX-7's / Re: BOOSTED FD BUILD.
« Last post by Casey on December 12, 2018, 05:16:06 PM »
  Great news Jon 
Pages: [1] 2 ... 5