Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - boosted

Pages: [1] 2 ... 496
1
Rotary and General Chit-Chat / Re: NSU....
« on: December 18, 2018, 07:21:12 PM »
It does look like the paints holding it together...

Sent from my SM-N950F using Tapatalk


2
Rotary and General Chit-Chat / NSU....
« on: December 18, 2018, 10:18:08 AM »
look what i found in copart....

https://www.copart.co.uk/lot/52787268

3
3rd generation RX-7's / Re: BOOSTED FD BUILD.
« on: December 17, 2018, 07:16:23 PM »
spoke to soon....3 hours in A&E today.... :violent1:  got some magic cream....

4
RX-8's / Re: She's Back On the Road not completely done but good enough
« on: December 16, 2018, 05:07:24 AM »
Have a good run out today, few beeps!!!

Sent from my SM-N950F using Tapatalk


5
Rotary and General Chit-Chat / Re: Rotus Project Build
« on: December 13, 2018, 09:44:17 PM »
Must be looking at old photo..tried hylomar nope. Original rubber seal dried up and cracked..made 1 out of ptfe 1mm thick white sheet i procured from work.  Made a gasket a ring with the stud holes stamped out.

Sent from my SM-N950F using Tapatalk


6
Rotary and General Chit-Chat / Re: Rotus Project Build
« on: December 13, 2018, 09:19:29 PM »
I used a few materials and the ptfe 1 i made has been onit 3 years no leak. Ill link tilton pedals..demon tweeks.

Sent from my SM-N950F using Tapatalk


7
Rotary and General Chit-Chat / Re: Rotus Project Build
« on: December 13, 2018, 04:11:46 PM »
Switches behind.
Clutch switch alters idle in neutral. Id set a 1200 rpm idle brings the oil press up.

Sent from my SM-N950F using Tapatalk


8
Rotary and General Chit-Chat / Re: Rotus Project Build
« on: December 13, 2018, 04:09:42 PM »
Tilton 600 series..floor or overhung mount. 2 pedal £280 from Merlin.
I use the rx8 clutch and brake switch...2 ally tabs on top of pedals.

Sent from my SM-N950F using Tapatalk


9
Rotary and General Chit-Chat / Re: Clive's 400 BHP Super GT RX-8 Race Car
« on: December 13, 2018, 03:00:34 PM »
https://manualzz.com/doc/7305889/ibc-r-user-manual---from-tuner-tools

its all here.. p19 external wastegate plumbing with solenoid port numbers.

10
Rotary and General Chit-Chat / Re: Clive's 400 BHP Super GT RX-8 Race Car
« on: December 13, 2018, 07:28:08 AM »
https://id-workz.co.uk/gizzmo-ibc-r-boost-controller

this is the link to the Gizzmo... Duty can be changed per 500 rpm so different boost settings at different rpms,launch  low rpm low boost wheel hook up boost.  4K high boost Rocket launcher mode

I have this fitted on my car but not controlling boost, prob take me an hour to get out...happy to send to you and you have a back up if the Adaptronic cant control the wastegate....and can it change boost dependent on rpm?

You could install (cable tie stylee)  :violent1: :13: live and neutral, run the solenoid and vac hose through to engine bay before you go to Pips?  got the solenoid etc but you got that already...

Ive got the manual as well etc.

Upto you ....could save a few ££££ and wasted journey, its doing nothing on my car atmo. :P


11
Rotary and General Chit-Chat / Re: Clive's 400 BHP Super GT RX-8 Race Car
« on: December 12, 2018, 09:50:46 PM »
Whohoo...Go Christine...

Sent from my SM-N950F using Tapatalk


12
1st generation RX-7's / Re: Another Boosted thread FB time....
« on: December 12, 2018, 04:13:44 PM »
Few days to contemplate sale and happy its gone. To many cars and not enough cash to do them all. Once it done wouldve parked up like eunos so best somebody else enjoys it.

Sent from my SM-N950F using Tapatalk


13
3rd generation RX-7's / Re: BOOSTED FD BUILD.
« on: December 12, 2018, 04:11:28 PM »
Well been out for a hour and all good. Straight as a die at speed. Brakes blimin good no shaking, boost temps all in check...happy bunny.
Got a few funny looks...and a few thumbs up from school kids,pesky little shits!!!
And in other news, im feeling great...about a week now hoping not to tempt fate....

Sent from my SM-N950F using Tapatalk


14
Rotary and General Chit-Chat / Re: Rotus Project Build
« on: December 12, 2018, 04:07:01 PM »
Heres mine, ill dig reciept out as that obp seems quite expensive....
Looking about they seem tobe doing them with flyby wire now too.
Looks like my go pedal pedal offset in piccy. Its not. The ally chequer plate is a little heel bridge as size 8 feet i could get a good pivot/pedal feel...epic now.
Servoless wilwoods dynalites with mintex 1157s awesome brakes...pads dont wear either been in 4 years lol  dont seem to wear out.

Sent from my SM-N950F using Tapatalk


15
Rotary and General Chit-Chat / Re: Rotus Project Build
« on: December 12, 2018, 01:13:49 AM »
I run tilton pedal box. Clutch and brake.floor mounted with rx8 throttle pedal fly by wire.
Your gonna need to keep the fly by wire rx8 throttle pedal.
I dont have an issue with the 2. Careful positioning of the pedals and i fitted a heel plate..ill get a piccy later.


Sent from my SM-N950F using Tapatalk


Pages: [1] 2 ... 496